Kubota VS 220 Скачать руководство пользователя страница 27

Страница: 27 / 154

Getting familiar with the machine

Applications of the

machine

This PTO shaft driven machine is suitable for amongst others

spreading granular and powdery fertiliser types on the field and

grazing land. The machines can also be used as salt, sand and fine

split spreader in road construction and maintenance.

It is attached in the three-point linkage of the tractor:

•

Cat. II for the VS 600-1000

•

Cat. I/II for the VS 400 / 500 and VITI

•

Cat. I for the VS 220 / 330

Border spreading is possible by using the following:

•

border spreading plate,

•

border-spreading cylinder.

Other fields of use

Powder, salt and gravel spreading is possible with type VS 220-

330,600-800-1000.

A choice of accessories and modifications to the machine is available.



See chapter »Accessories« on page 137 for possibilities.

Environment

This fertiliser spreader is equipped with a calibration container and

border-spreading plate that comply with environmental standard

13739-1

SuperFlow spreading

system

The pendulum spreader spreads fertilisers, powders, grains, seeds,

salts, etc. with a spreading spout. The movement of the spreading

spout is symmetrical, and therefore the spreading pattern is also

symmetrical. The spreading quantity is regulated by a dosing plate

under the hopper. Both of the dosing plates are located right on top of

the middle of the discharge opening to the spreading spout.

At the beginning of the spreading spout, the movement speed of the

granules is low. The speed increases towards the end of the spreading

spout.

Less dust and grain breakage

Grain breakage and powder formation are prevented by gradual

speed change in the spreading spout.

The agitator mounted below in the hopper provides for a steady,

constant stream of fertiliser, powders, seeds, etc. to the spreading

spout. Moreover, the agitator prevents the chunks of fertiliser from

blocking one or more dosing openings.

Transverse distribution

The movement of the spreading spout brings about a strong

distribution to both sides without ejecting far behind. This prevents

irregularity of the distribution due to and strongly sloping fields.

Hopper

Spreading spout

Spreading bracket

Spreading spout

Содержание VS 220



























































































































































Результаты поиска

Содержание VS 220

Отзывы:

Бренды по названию

Популярные бренды

Kubota VS 220, Руководство пользователя

Результаты поиска

Содержание VS 220

Отзывы:

Бренды по названию

Популярные бренды