manualshive.com logo in svg

Kubota VS 220, Руководство пользователя

Поделиться
Скачать
Kubota VS 220 Скачать руководство пользователя страница 112

Use on the land

112

Working method on 

the headland

The  way  you  have  to  stop  and  turn  at  the  headland  depends  on 

whether you

•

do boundary-track spreading from the sprayer tramline with the 

border-spreading cylinder

•

or one-sided boundary spreading with the border-spreading plate.

Do the following when spreading the headland:

Spreading headland when using 

the border-spreading cylinder

Spread the field edges all around with the border-spreading 

cylinder.

See paragraph »Border spreading« on page 113.

Stop the spreading by closing the dosing unit of the machine when 

the tractor’s front wheel reaches the inside headland track.

Do not switch off the PTO shaft.

After turning at a distance of a half to 3/4 working width of a 

headland track open the dosing units again.

Spreading headland when using 

the border spreading plate

Spread the field edges as described in the paragraph »One-sided 

boundary spreading with the border spreading plate« on page 113.

Spread a full-field round in the first sprayer tramline adjacent to the 

border spreading pattern.

Stop the spreading during the one-sided boundary spreading by 

closing the dosing units just before you are going to turn.

Do not switch off the PTO shaft.

After turning at a distance of a half to 3/4 working width of a 

headland track open the dosing units again.

Over and underdosing

Depending on soil or crop composition, it is preferable to spread more 

or less fertiliser locally. This could for instance be where experience 

has shown that certain parts of the field need more or less fertiliser 

than others.

It is possible to over or underdose by

•

driving faster whereby the spreading quantity per acre is reduced,

•

drive slower, which will increase the spreading volume per acre,

I

NDICATION

The rpm of the tractor engine (therefore also of the PTO shaft) must 

remain constant (concerning distributing fertiliser along the width).

The driving speed can only be adjusted by selecting another 
speed!

Содержание VS 220



























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды