Kubota RT120Q Скачать руководство пользователя страница 159 | Manualshive

Страница: 159 / 219

background image

Service - 158

RT120Q Operator’s Manual

Recommended Lubricants/Service Key

Approved Coolant

Beginning March 14, 2016

, this unit was filled with

red

coolant meeting Deutz

®

DQC CB-14 before

shipment from factory. Add or replace only with coolant meeting this specification. This coolant is available,

pre-diluted, from your Ditch Witch

®

dealer as part number 255-1053. Contact your Deutz service partner

for a full list of approved coolants meeting DQC CB-14. In an emergency, non-Deutz approved, heavy duty
diesel engine coolant meeting ASTM D6210 may be used. Change to DQC CB-14 coolant as soon as
practical.

Prior to March 14, 2016

, this unit was filled with

yellow

John Deere

®

Cool-Gard

®

coolant before shipment

from factory. Add only John Deere Cool-Gard (p/n 255-006) or any fully-formulated, ethylene glycol based,
low-silicate, heavy-duty diesel engine coolant meeting ASTM specification D6210. Switch to the new
approved

red

coolant described above at the next change interval.

Engine Oil Temperature Chart

NOTICE:

•

Use only pre-diluted or concentrated coolant mixed with distilled water. Do not use tap water.

•

Do not use water or high-silicate automotive-type coolant. This will lead to engine damage or
premature engine failure.

•

Do not mix heavy-duty diesel engine coolant and automotive-type coolant. This will lead to coolant
breakdown and engine damage.

t37om047w.eps

SAE 0W-30

SAE 0W-40

SAE 5W-30

SAE 5W-40

SAE 10W-30

SAE 10W-40

SAE 15W-40

SAE 20W-50

Temperature range anticipated before next oil change

«
...
157
158
159
160
161
...
»

Содержание RT120Q




























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для RT120Q

Бренд: Ditch Witch Страницы: 103

Бренд: imants Страницы: 52

Бренд: Zetor Страницы: 197

Бренд: CAMSO Страницы: 20

Бренд: New Holland Страницы: 2

Бренд: New Holland Страницы: 24

Бренд: New Holland Страницы: 61

Бренд: LS Страницы: 11

Бренд: Pasquali Страницы: 65

Бренд: Zetor Страницы: 76

Бренд: Captain Страницы: 121

Бренд: Geax Страницы: 77

Бренд: Komatsu Страницы: 4

Proxima Plus 100

Бренд: Zetor Страницы: 34

Бренд: Pow’R’kraft Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды