Kubota LA344 Скачать руководство пользователя страница 56

Страница: 56 / 74

3.3 3rd function solenoid valve

3.3.1 Checking 3rd function solenoid valve

continuity

1. Disconnect solenoid valve connector.

(1) Solenoid valve connector

2. Measure the resistance with an ohmmeter between

terminal 1 and terminal 2.

Solenoid valve side

Terminal 1

Terminal 2

3. If the measurement greatly differs from specified

value, replace the solenoid valve.

Resistance

Approx. 3.8 Ω

3.3.2 Checking connector voltage of 3rd

function solenoid valve

1. Disconnect solenoid valve connector.

(1) Solenoid valve connector

2. Turn the main switch on and push the front

hydraulic valve main switch (ON position), then
push the activation switch..

3. Measure the voltage between terminal 1 and

terminal 2.

Wire harness side

Terminal 1

Terminal 2

4. If the measurement differs from the battery voltage,

wire harness is damaged.

4. Disassembling and

assembling

4.1 Removing and attaching front

loader

IMPORTANT

• To remove the loader, park the tractor on flat

and hard ground, apply the parking brake.
To start the engine or use the hydraulic control
valve, always stay in the operator's seat.

4.1.1 Removing loader

CAUTION

• Make sure an approved bucket is attached

before removing the loader from the tractor.

SERVICING

3. Checking and adjusting

3. FRONT LOADER

LA344, LA344S

3-19

KiSC issued 02, 2017 A

Содержание LA344











































































Результаты поиска

Содержание LA344

Отзывы:

Похожие инструкции для LA344

Бренды по названию

Популярные бренды

Kubota LA344, Руководство по ремонту

Результаты поиска

Содержание LA344

Отзывы:

Похожие инструкции для LA344

Бренды по названию

Популярные бренды