Kubota LA344 Скачать руководство пользователя страница 54

Страница: 54 / 74

20. Set the stand lever to the

low

position.

(1) Stand lever

21. Fasten the seat belt.
22. Get the engine started, roll back the bucket and

move up the boom, both to maximum.

23. Stop the engine.
24. Move the hydraulic-control-lever to the

dump

position until the bucket comes to a complete stop.

25. Make sure that the stands are folded as specified.
26. Fasten the seat belt.
27. Get the engine started and raise the engine speed

up to the following speed.

Engine speed

1800 rpm

28. Slowly dump the bucket until the stand touches the

boom.

29. Slide the stand lever upward direction, and then

slide the stand lever left side completely as shown
in the following figure.

(1) Stand lever

30. Hold the stand by stand hook.

(1) Stand

(2) Stand hook

3.2 Front hydraulic valve main

switch and relay

3.2.1 Checking front hydraulic valve main

switch continuity

1. Disconnect the front hydraulic valve main switch

connector.

(1) Front hydraulic valve main

switch

2. Measure the resistance with an ohmmeter between

terminal RB and terminal B.

SERVICING

3. Checking and adjusting

3. FRONT LOADER

LA344, LA344S

3-17

KiSC issued 02, 2017 A

Содержание LA344











































































Результаты поиска

Содержание LA344

Отзывы:

Похожие инструкции для LA344

Бренды по названию

Популярные бренды

Kubota LA344, Руководство по ремонту

Результаты поиска

Содержание LA344

Отзывы:

Похожие инструкции для LA344

Бренды по названию

Популярные бренды