Kubota LA344 Скачать руководство пользователя страница 51

Страница: 51 / 74

3. Checking and adjusting

3.1 Loader stand

3.1.1 Adjusting height of loader stand

1. Make sure that the stand lever is at its low position

as shown in the following figure.

(1) Stand lever

2. Raise the boom until the bucket-fulcrum-pin comes

up to the height of the boom-fulcrum-pin.

3. Roll back the bucket to maximum.

(1) Bucket fulcrum pin
(2) Boom fulcrum pin

(A) Same height

4. Stop the engine.
5. Apply the adjusting bolts to the right and left stand

adjusting blocks as shown in the following figure.

(1) Adjusting block
(2) Adjusting bolt

(3) Lock nut

IMPORTANT

• Be sure to apply the bolts all the way to

prevent the damage of the stand.

NOTE

• There is no need to tighten up the lock nuts.

6. Move the hydraulic-control-lever to the

dump

position, and check to see if the stands are folded
as specified.

7. Fasten the seat belt, and start the engine.
8. Move the hydraulic control lever to the

dump

position until the hydraulic pressure gets relieved.

9. Lower the boom to put the bucket on the ground.

(1) Bucket

(2) Stand

3. FRONT LOADER

SERVICING

3.Checking and adjusting

3-14

LA344, LA344S

KiSC issued 02, 2017 A

Содержание LA344











































































Результаты поиска

Содержание LA344

Отзывы:

Похожие инструкции для LA344

Бренды по названию

Популярные бренды

Kubota LA344, Руководство по ремонту

Результаты поиска

Содержание LA344

Отзывы:

Похожие инструкции для LA344

Бренды по названию

Популярные бренды