Kubota LA344 Скачать руководство пользователя страница 48

Страница: 48 / 74

SERVICING

1. Troubleshooting for front loader

Symptom

Probable cause and checking

procedure

Solution

Refer-

ence

page

Boom does not rise.

1. Control valve is damaged.

Repair or replace control valve.

Tractor

WSM

2. Boom cylinder is damaged.

Repair or replace boom cylinder.

3-28

3. Control lever linkage is dam-
aged.

Repair or replace control lever
linkage.

Tractor

WSM

4. Hydraulic pump is damaged.

Repair or replace hydraulic
pump.

Tractor

WSM

5. Relief valve spring is dam-
aged.

Replace relief valve spring.

Tractor

WSM

6. Relief valve is dirty.

Clean relief valve.

Tractor

WSM

7. Oil filter is clogged.

Clean or replace oil filter.

—

8. Hydraulic hose is damaged.

Replace hydraulic hose.

3-28

Boom does not lower.

1. Control valve is damaged.

Repair or replace control valve.

Tractor

WSM

2. Control lever linkage is dam-
aged.

Repair or replace control lever
linkage.

Tractor

WSM

Boom speed is insufficient.

1. Boom cylinder tube is worn or
damaged.

Replace boom cylinder tube.

3-28

2. Boom cylinder piston ring (pis-
ton seal and O-ring) is worn or
damaged.

Replace boom cylinder piston
ring (piston seal and O-ring).

3-30

3. Oil leaks from tube joints.

Repair tube joints.

—

4. Relief valve setting pressure is
too low.

Adjust relief valve.

Tractor

WSM

5. Transmission fluid is insuffi-
cient.

Fill transmission fluid.

Tractor

WSM

6. Relief valve is dirty.

Clean relief valve.

Tractor

WSM

Bucket does not move.

1. Control valve is damaged

Repair or replace control valve.

Tractor

WSM

2. Bucket cylinder is damaged.

Repair or replace bucket cylin-
der.

3-28

(Continued)

SERVICING

1. Troubleshooting for front loader

3. FRONT LOADER

LA344, LA344S

3-11

KiSC issued 02, 2017 A

Содержание LA344











































































Результаты поиска

Содержание LA344

Отзывы:

Похожие инструкции для LA344

Бренды по названию

Популярные бренды

Kubota LA344, Руководство по ремонту

Результаты поиска

Содержание LA344

Отзывы:

Похожие инструкции для LA344

Бренды по названию

Популярные бренды