Kubota L47TL Скачать руководство пользователя страница 155 | Manualshive

Страница: 155 / 159

background image

129

TROUBLESHOOTING

TROUBLESHOOTING

(A) Error message is displayed at here

Display on IntelliPanel(TM)

Trouble Item (Affected Model)

Operator's action

ERROR No. 20
CAN NG

Communication error between
ECU and IntelliPanel(TM)

Contact your local KUBOTA Dealer.

ERROR No. 30
ECU Memory DEVICE NG

ECU's memory device is in
trouble

ERROR No. 40
Input Voltage NG

Input voltage of lever sensor
from ECU is in trouble

ERROR No. 80
Range Shift SENSOR NG

Sensor for range gear shift lever
is in trouble

Contact your local KUBOTA Dealer.
The speed range (H, M and L) is not displayed in the
LCD screen. The range gear shift lever still works to
select the H, M and L speeds. In selecting M or L,
however, the feeling is somewhat different at a start,
stop and other actions.

ERROR No. 81
HST Pedal SENSOR NG

Sensor for speed control pedal
is in trouble

Contact your local KUBOTA Dealer.
The speed control pedal cannot be used to run the
tractor.

ERROR No. 82
Swash Plate SENSOR NG

Sensor for swash plate of HST is
in trouble

Contact your local KUBOTA Dealer.
The tractor can travel both forward and backward, but
with a drop in maximum speed.

ERROR No. 84
Throttle SENSOR NG

Sensor for engine throttle is in
trouble

Contact your local KUBOTA Dealer.
With the STALL GUARD or AUTO H-DS/STALL
GUARD mode being selected, the tractor automatically
gets in the MANUAL mode.

ERROR No. 87
Engine Speed SENSOR NG

Sensor for engine revolution is
in trouble

ERROR No. 90
HST-F SOLENOID NG

Proportional valve for forward is
in trouble

Contact your local KUBOTA Dealer.
The tractor cannot travel forward (backward only).

ERROR No. 91
HST-R SOLENOID NG

Proportional valve for reverse is
in trouble

Contact your local KUBOTA Dealer.
The tractor cannot travel backward (forward only).

ERROR No. 92
Hi-Lo SOLENOID NG

Motor for Hi-Lo shift is in trouble Contact your local KUBOTA Dealer.

Using the H-DS lever, the Lo speed alone can be
selected (Hi speed not selectable).
In the HST mode, only the STALL GUARD and
MANUAL modes can be selected.

«
...
153
154
155
156
157
...
»

Содержание L47TL
































































































































































Отзывы:

Нет отзывов

Похожие инструкции для L47TL

10 Cab Series 4510C

Бренд: Mahindra Страницы: 115

Бренд: New Holland Страницы: 41

Бренд: Pig Страницы: 35

Бренд: Jonsered Страницы: 56

Бренд: Cub Cadet Страницы: 33

Бренд: Pasquali Страницы: 48

Бренд: Ignite Страницы: 40

Бренд: Kellfri Страницы: 16

Бренд: Husqvarna Страницы: 36

Бренд: Husqvarna Страницы: 18

Straw Harrow - 7.5m

Бренд: Claydon Страницы: 28

Бренд: Montana Страницы: 26

Бренд: Hagie Страницы: 127

Бренд: Meyer Страницы: 12

Бренд: Mitsubishi Страницы: 24

Бренд: Mitsubishi Страницы: 177

McCormick Farmall Super C

Бренд: International Harvester Company Страницы: 101

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды