background image

107

PERIODIC SERVICE OF THE TRACTOR

B

Adjusting Rear Parking Brake Lever

To avoid personal injury or death:

A

Stop the engine and chock the wheels before
checking parking brake.

1. Make sure that the rear parking brake works by pulling

the lever one notch.

2. If adjustment is needed, loosen the lock nut and adjust

the parking brake cable length with in acceptable limit.

3. Retighten the lock nut.

B

Checking Battery Condition

To avoid the possibility of battery explosion:
For the refillable type battery, follow the
instructions below.

A

Do not use or charge the refillable type battery
if the fluid level is below the LOWER (lower limit
level) mark. Otherwise, the battery component
parts may prematurely deteriorate, which may
shorten the battery's service life or cause an
explosion. Check the fluid level regularly and
add distilled water as required so that the fluid
level is between the UPPER and LOWER levels.

To avoid personal injury or death: 

A

Never remove the vent caps while the engine is
running.

A

Keep electrolyte away from eyes, hands and
clothes. If you are spattered with it, wash it
away completely with water immediately and
get medical attention.

A

Wear eye protection and rubber gloves when
working around the battery.

Mishandling the battery shortens the service life and adds
to maintenance costs.
The original battery is maintenance free, but needs some
servicing.
If the battery is weak, the engine will be difficult to start
and the lights will be dim. It is important to check the
battery periodically.

C

How to read the indicator (if equipped)

Check the battery condition by reading the indicator.

Parking position

from 1 notch

(1) Rear parking brake lever
(2) Release button

(A) "PULL"

(1) Parking brake cable
(2) Lock nut

(A) "PULL"

The factory-installed battery is of non-refillable 
type. If the battery is weak, do not charge the battery 
but replace it with new one.

State of indicator display

Green

Specific gravity of electrolyte and quality of 
electrolyte are both in good condition.

Black

Needs charging battery.

White

Needs changing battery.

Содержание L47TL
































































































































































Отзывы: