Kubota L47TL Скачать руководство пользователя страница 132

Страница: 132 / 159

PERIODIC SERVICE OF THE TRACTOR

106

Adjusting Fan Belt Tension

To avoid personal injury or death:

Be sure to stop the engine before checking belt
tension.

1. Stop the engine and remove the key.
2. Apply moderate thumb pressure to belt between

pulleys.

3. If tension is incorrect, loosen the alternator mounting

bolts and, using a lever placed between the alternator
and the engine block, pull the alternator out until the
deflection of the belt falls within acceptable limits.

4. Replace fan belt if it is damaged.

Adjusting Brake Pedal

To avoid personal injury or death:

Stop the engine and chock the wheels before
checking brake pedal.

1. Release the parking brake.
2. Slightly depress the brake pedals and measure free

travel at top of pedal stroke.

3. If adjustment is needed, loosen the lock nut and turn

the turnbuckle to adjust the rod length within
acceptable limits.

4. Retighten the lock nut.

Proper fen belt
tension

A deflection of between 7 to 9 mm
(0.28 to 0.34 in.) when the belt is
pressed in the middle of the span.

(1) Bolt

(A) Check the belt tension
(B) To tighten

Proper brake pedal
free travel

15 to 20 mm (0.6 to 0.8 in.) on
the pedal.

Keep the free travel in the right
and left brake pedals equal.

(1) Lock nut
(2) Turnbuckle

(A) Free travel

Содержание L47TL
































































































































































Результаты поиска

Содержание L47TL

Отзывы:

Похожие инструкции для L47TL

Бренды по названию

Популярные бренды

Kubota L47TL, Руководство оператора

Результаты поиска

Содержание L47TL

Отзывы:

Похожие инструкции для L47TL

Бренды по названию

Популярные бренды