Kubota K008-5 страница 78 Скачать руководство пользователя | Manualshive

Страница: 78 / 168

background image

76

W9215-8135-1

06/2021

Operation

Seat belt



Pull the seat belt (1) out of the belt retractor, wrap it around your
waist and latch it in the buckle (2).



Make sure that the seat belt fits tightly and the buckle is latched
in place.



To release the seat belt, press the red button on the buckle and
slowly guide the belt back into the belt retractor.

Field of view

When the operator is sitting in the driver’s seat, the field of view is partially impaired by the machine as some areas
are obscured. It is important to be familiar with and understand the visibility conditions when operating the ma-
chine. Within the machine’s immediate radius of action, this helps to detect hazards that may cause accidents ear-
ly on and thus prevent them.

The illustration shows the field of view and the areas that are not vis-
ible. The field of view varies from operator to operator and depend-
ing on the position of the seat.

1.

Field of view within a radius of 12 m

2.

Field of view in the immediate area



Take a seat in the operator’s seat and adjust the seat (page 75).

If the engine compartment cover is not locked, the operator's seat can tilt backwards. Before buckling
up the seat belt, check that the engine compartment cover is locked and secured with a padlock.

Risk of accidents!

Operating the machine without wearing the seat belt is prohibited!
The belt buckle is equipped with a sensor. This sensor detects whether the seat belt is fastened and
whether the tongue is inserted and latched in the buckle.
If the engine starts and the seat belt is not latched inside the buckle, warning beep sounds every 2
seconds.

- Only operate the machine with the seat belt fastened.

Do not operate the excavator without the seat belt fas-
tened.

When removing the seat belt, store the belt straight. If
you store the belt without straightening it, the belt lock
in the belt reactor may not work properly.
This machine is equipped with an orange seat belt
which is highly visible when the operator fastens it.

STOP

STOP

1

2

STOP

«
...
76
77
78
79
80
...
»

Содержание K008-5









































































































































































Отзывы:

Нет отзывов

Похожие инструкции для K008-5

Бренд: jcb Страницы: 332

Бренд: Garbin Страницы: 51

Бренд: Woody Страницы: 31

Бренд: Gravely Страницы: 66

Бренд: AVANT Страницы: 18

Бренд: AVANT Страницы: 18

Бренд: AVANT Страницы: 28

Бренд: AVANT Страницы: 40

Бренд: AVANT Страницы: 36

Бренд: AVANT Страницы: 40

Бренд: AVANT Страницы: 40

500 Series 2019

Бренд: AVANT Страницы: 64

Бренд: AVANT Страницы: 84

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды