Kubota K008-5 страница 17 Скачать руководство пользователя

Страница: 17 / 168

Safety rules

W9215-8135-1

06/2021

Safety symbols

The following terms and hazard symbols are used in these operating instructions:

Identifies important operating procedure information that may not be immediately evident to the op-
erator.

Identifies operating procedures that must be followed exactly to prevent damage to the excavator or
other property.

Identifies operating procedures that must be followed exactly to prevent danger to persons.

Identifies possible hazards in the handling of batteries.

Identifies possible hazards from caustic materials (battery acid).

Identifies possible hazards from explosive materials.

Prohibits the use of fire, ignition sources, and smoking.

Prohibits the spraying of water.

Identifies operating procedures for the proper disposal and storage of ensuing waste materials.

STOP

Содержание K008-5









































































































































































Результаты поиска

Содержание K008-5

Отзывы:

Похожие инструкции для K008-5

Бренды по названию

Популярные бренды

Kubota K008-5, Руководство по эксплуатации

Результаты поиска

Содержание K008-5

Отзывы:

Похожие инструкции для K008-5

Бренды по названию

Популярные бренды