Kubota K008-5 Скачать руководство пользователя

Страница: 156 / 168

154

W9215-8135-1

06/2021

Taking out of service and storage

Start-up after taking out of service



If necessary, clean the excavator thoroughly (page 132).



Check the hydraulic oil for condensate water. Replace the oil if necessary.



Install the battery (page 143).



Check the safety devices for proper operation.



Carry out the pre-operational services (page 68). If damage is detected during start-up, repair the damage
before proceeding.



If the safety inspection is due while the vehicle has been taken out of service, the inspection must be per-
formed before start-up.



Start the engine (page 78). Run the excavator at idle and check all functions.

Содержание K008-5









































































































































































Результаты поиска

Содержание K008-5

Отзывы:

Похожие инструкции для K008-5

Бренды по названию

Популярные бренды

Kubota K008-5, Руководство по эксплуатации

Результаты поиска

Содержание K008-5

Отзывы:

Похожие инструкции для K008-5

Бренды по названию

Популярные бренды