manualshive.com logo in svg

Kubota G23, Руководство по ремонту


Поделиться
Скачать
background image

GENERAL

G23, G26, WSM

G-43

(EU)

Checking Radiator Hose and Clamp

 CAUTION

To avoid personal injury :

• Be sure to stop the engine and remove the key before

checking radiator hose and clamps.

Check to see if radiator hoses are properly secured every 200

hours of operation or six months, whichever comes first.
1. If hose clamps are loose or water leaks, tighten clamps

securely.

2. Replace hoses and tighten hose clamps securely, if radiator

hoses are swollen, hardened or cracked.

3. Properly dispose of used coolant.

Replace hose and hose clamps every 2 years or earlier if

checked and found that hoses are swollen, hardened or cracked.

Q

Precaution at Overheating

Take the following actions in the event the coolant temperature

be nearly or more than the boiling point, what is called
"Overheating".
1. Stop the machine operation in a safe place and keep the engine

unloaded idling.

2. Do not stop the engine suddenly, but stop it after about 5

minutes of unloaded idling

3. Keep yourself well away from the machine for further 10

minutes or while the steam is blown out.

4. Checking that there is no danger such as burn, get rid of the

causes of overheating.

9Y1210294GEG0046US0

Checking Intake Air Line

1. Check to see that hoses and hose clamps are tight and not

damaged.

2. If hoses and clamps are found worn or damaged, replace or

repair them at once.

9Y1210294GEG0047US0

(1) Radiator Core (2 pcs)

(2) Radiator Hose (2 pcs)

(1) Hose (G23)
(2) Hose Clamp (G23)
(3) Hose (G26)
(4) Hose Clamp (G26)

[A] G23
[B] G26

KiSC issued 08, 2009 A

Содержание G23
























































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для G23

Toro 30339 Operator'S Manual preview
30339
Бренд: Toro Страницы: 52
MTD 113-112 Operating/Service Instructions Manual preview
113-112
Бренд: MTD Страницы: 9
Encore 34K350Z Operator'S Manual preview
34K350Z
Бренд: Encore Страницы: 20
Yard-Man 131784G Owner'S Manual preview
131784G
Бренд: Yard-Man Страницы: 20
Yard-Man 1060-5 Owners Operating Manual And Parts List preview
1060-5
Бренд: Yard-Man Страницы: 11
Sabo 47-ECONOMY Operator'S Manual preview
47-ECONOMY
Бренд: Sabo Страницы: 124
Sabo 102-17H B Operator'S Manual preview
102-17H B
Бренд: Sabo Страницы: 280
Gtech RCLM001 Operating Manual preview
RCLM001
Бренд: Gtech Страницы: 32
Webb 193801003 Original Instructions Manual preview
193801003
Бренд: Webb Страницы: 24
Gartenmeister GM-HM 20 Operating Instructions Manual preview
GM-HM 20
Бренд: Gartenmeister Страницы: 52
Poulan Pro 183249 Owner'S Manual preview
183249
Бренд: Poulan Pro Страницы: 48
Toro Reelmaster 03485 Operator'S Manual preview
Reelmaster 03485
Бренд: Toro Страницы: 24
inventiv INV B4037 P Translation From Original Instruction Manual preview
INV B4037 P
Бренд: inventiv Страницы: 173
Gardena PowerMax 1100/32 Operator'S Manual preview
PowerMax 1100/32
Бренд: Gardena Страницы: 10
Yard-Man Series 12A-979-401 Owner'S Manual preview
Series 12A-979-401
Бренд: Yard-Man Страницы: 32
Toro 04030 Operator'S Manual preview
04030
Бренд: Toro Страницы: 40
Toro 03673 Reelmaster 5410-G Operator'S Manual preview
03673 Reelmaster 5410-G
Бренд: Toro Страницы: 48
Talon AM3051SP Owner'S Manual preview
AM3051SP
Бренд: Talon Страницы: 10

Бренды по названию

Популярные бренды

Загрузить еще бренды