manualshive.com logo in svg

Kubota G23, Руководство по ремонту

Поделиться
Скачать
Kubota G23 Скачать руководство пользователя страница 328

MOWER

G23, G26, WSM

7-S15

(EU)

[3] SERVICING

Backlash between Spiral Gear on Input Shaft and Spiral Gear
on Output Shaft

1. Remove the cap (7).
2. Place fuse to the spiral gear (5) on the output shaft (4).
3. Push the input shaft (3) and pull the output shaft (4).
4. Turn the input shaft two to three turns.
5. Take out the fuse, and measure the thickness of the fuse with

an outside micrometer.

6. After adjusting the backlash between the spiral gear on the input

shaft (3) and the spiral gear (5) on the output shaft (4), install the
shims (8), (9).

(Reference)

RCK45-G23, RCK54-G26

• Thickness of shim (1) :

0.2 mm (0.0079 in.)
0.3 mm (0.0118 in.)
0.5 mm (0.0197 in.)

• Thickness of shim (6) :

0.2 mm (0.0079 in.)
0.3 mm (0.0118 in.)
0.5 mm (0.0197 in.)

9Y1210294MOS0017US0

Backlash between spiral 
gears

Factory specification

0.10 to 0.30 mm
0.0039 to 0.0118 in.

Allowable limit

0.40 mm
0.0157 in.

(1) Shim
(2) Spiral Gear
(3) Input Shaft
(4) Output Shaft
(5) Spiral Gear
(6) Shim
(7) Cap
(8) Shim
(9) Shim

A : Place fuse
B : Push in
C : Pull

KiSC issued 08, 2009 A

Содержание G23
























































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды