manualshive.com logo in svg

Kubota D1503-M-E3, Руководство оператора, Страница: 27 / 47

Поделиться
Скачать
Kubota D1503-M-E3 Скачать руководство пользователя страница 27

15

PERIODIC SERVICE

EN

GLISH

B

Fuel filter cartridge replacement

1. Replace the fuel filter cartridge with a new one every

400 operating hours.

2. Apply fuel oil thinly over the gasket and tighten the

cartridge into position by hand-tightening only.

3. Finally, vent the air.

A

Replace the fuel filter cartridge periodically to prevent
wear of the fuel injection pump plunger or the injection
nozzle, due to dirt in the fuel.

ENGINE OIL

To avoid personal injury:

A

Be sure to stop the engine before
checking and changing the engine
oil and the oil filter cartridge.

A

Do not touch muffler or exhaust
pipes while they are hot; Severe
burns could result. Always stop the
engine and allow it to cool before
conducting inspections,
maintenance, or for a cleaning
procedure. 

A

Contact with engine oil can damage
your skin. Put on gloves when using
engine oil. If you come in contact
with engine oil, wash it off
immediately.

A

Be sure to inspect the engine, locating it on a level
place. If placed on gradients accurately, oil quantity
may not be measured.

B

Checking oil level and adding engine oil

1. Check the engine oil level before starting or more than

5 minutes after stopping the engine.

2. Remove the oil level gauge, wipe it clean and reinstall

it.

3. Take the oil level gauge out again, and check the oil

level.

(1) Fuel filter cartridge
(2) Air vent plug
(3) O ring
(4) Pipe joint
(5) Cover

(1) Oil filler plug
(2) Oil level gauge

[Lower end of oil level gauge]
(A) Engine oil level within this
range is proper.

E.book  15 ページ  ２００９年４月２３日　木曜日　午前１０時３１分

Содержание D1503-M-E3
















































Отзывы:

Нет отзывов