Kubota BX2350D Скачать руководство пользователя | Manualshive

Страница: 95 / 102

background image

75

STORAGE

ENGLISH

STORAGE

To avoid personal injury:

A

Do not clean the machine while the engine is
running.

A

To avoid the danger of exhaust fume
poisoning, do not operate the engine in a
closed building without proper ventilation.

A

When storing, remove the key from the key
switch to avoid unauthorized persons from
operating the tractor and getting injured.

TRACTOR STORAGE

If you intend to store your tractor for an extended period
of time, follow the procedures outlined below. These
procedures will insure that the tractor is ready to operate
with minimum preparation when it is removed from
storage.
1. Check the bolts and nuts for looseness, and tighten if

necessary.

2. Apply grease to tractor areas where bare metal will

rust also to pivot areas.

3. Detach the weights from the tractor body.
4. Inflate the tires to a pressure a little higher than usual.
5. Change the engine oil and run the engine to circulate

oil throughout the engine block and internal moving
parts for about five minutes.

6. With all implements lowered to the ground, coat any

exposed hydraulic cylinder piston rods with grease.

7. Remove the battery from the tractor. Store the battery

following the battery storage procedures.
(See "Battery" in "EVERY 100 HOURS" in "PERIODIC
SERVICE" section.)

8. Keep the tractor in a dry place where the tractor is

sheltered from the elements. Cover the tractor.

9. Store the tractor indoors in a dry area that is protected

from sunlight and excessive heat. If the tractor must be
stored outdoors, cover it with a waterproof tarpaulin.
Jack the tractor up and place blocks under the front
and rear axles so that all four tires are off the ground.
Keep the tires out of direct sunlight and extreme heat.

A

When washing the tractor, be sure to stop the engine.
Allow sufficient time for the engine to cool before
washing.

A

Cover the tractor after the muffler and the engine have
cooled down.

REMOVING THE TRACTOR FROM

STORAGE

1. Check the tire air pressure and inflate the tires if they

are low.

2. Jack the tractor up and remove the support blocks

from under the front and rear axles.

3. Install the battery. Before installing the battery, be sure

it is fully charged.

4. Check the fan belt tension.
5. Check all fluid levels (engine oil, transmission/

hydraulic oil, engine coolant and any attached
implements).

6. Start the engine. Observe all gauges. If all gauges are

functioning properly and reading normal, move the
tractor outside. Once outside, park the tractor and let
the engine idle for at least five minutes. Shut the
engine off and walk around tractor and make a visual
inspection looking for evidence of oil or water leaks.

7. With the engine fully warmed up, release the parking

brake and test the brakes for proper adjustment as you
move forward. Adjust the brakes as necessary.

«
...
93
94
95
96
97
...
»

Содержание BX2350D







































































































Отзывы:

Нет отзывов

Похожие инструкции для BX2350D

Бренд: Nakayama Страницы: 24

AGROTRON 106 MK3

Бренд: DEUTZ-FAHR Страницы: 150

1500 BROCHURE 19.5-46

Бренд: MASSEY FERGUSON Страницы: 12

Бренд: Washtech Страницы: 30

Monogram ZCGP150PII

Бренд: GE Страницы: 2

MONOGRAM ZCGP150LII

Бренд: GE Страницы: 2

Бренд: GE Страницы: 24

Бренд: GE Страницы: 24

Monogram ZCGS150PSS

Бренд: GE Страницы: 2

Бренд: Still Страницы: 114

Бренд: Absima Страницы: 30

Бренд: Wallenstein Страницы: 52

Бренд: Ventrac Страницы: 31

Бренд: Belarus Страницы: 248

Бренд: Bad Boy Страницы: 152

Бренд: King Lift Equipment Страницы: 12

Бренд: Bolens Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды