Kubota AP-SD96 страница 24 Скачать руководство пользователя

Страница: 24 / 36

Section 3: Operating

AP-SD96 Silage Defacer 350-270MK

9/3/19

Table of Contents

Unhooking Quick Attach Hitch

DANGER

To avoid serious injury or death:

•

A crushing hazard exists while hooking-up and unhooking

to and from a quick attach hitch. Do not allow anyone to

stand between attachment and power machine while

approaching or backing away from the attachment. Do not

operate lift and/or tilt controls while someone is near the

power machine and/or attachment.

•

Always secure equipment with solid, non-concrete supports

before working under it. Never go under equipment

supported by concrete blocks or hydraulics. Concrete can

break, hydraulic lines can burst, and/or hydraulic controls

can be actuated even when power to hydraulics is off.

Refer to

Figure 3-7:

1. Shutdown the tractor before dismounting by following

the

“Power Machine Shutdown Procedure”

page 9.

2. Rest attachment (#1) on flat ground or on solid,

non-concrete supports if working on attachment.

3. Operate hydraulic control levers on power machine to

release all hydraulic system pressure to loader arm

lift cylinders and hitch tilt cylinder.

4. Dismount power machine and disconnect hydraulic

hose couplers (#1 & #2). Hang the hydraulic hoses

over top of attachment, ensuring they don’t make

contact with the ground.

5. Pull front loader lock handles up to remove pins from

bottom slots (#5) of hitch plates (#6).

6. Start power machine and raise attachment up

approximately 10 inches.

Tilt front of attachment slightly down and lower

attachment until both feet (#7) on rotor frame

stand (#8) make contact with the ground.

8. Slowly lower attachment until top of loader’s quick

attach hitch plate separates and clears top angle

bars (#4) of hitch plates (#6).

9. Using the back up camera or mirror, confirm there are

no people, animals or hazardous obstructions

behind the power machine.

10. Slowly operate the power machine in reverse while

making sure loader arms and quick attach hitch plate

do not interfere with attachment and its hydraulic

hoses.

11. If storing Silage Defacer for an extended period of

time, See

“Long-Term Storage”

on page 22.

Unhooking from Quick Attach Hitch

Figure 3-7

72596

Содержание AP-SD96





































Результаты поиска

Содержание AP-SD96

Отзывы:

Похожие инструкции для AP-SD96

Бренды по названию

Популярные бренды

Kubota AP-SD96, Руководство оператора

Результаты поиска

Содержание AP-SD96

Отзывы:

Похожие инструкции для AP-SD96

Бренды по названию

Популярные бренды