background image

4

PECO LIMITED WARRANTY FOR NEW PRODUCTS

A.  WHAT IS UNDER WARRANTY?

PECO extends the following warranties to the original purchaser of each new PECO consumer product subject 
to the following limitations

.

1.  PRODUCT WARRANTY:

 Any part of any consumer product, which is defective in material or 

workmanship as delivered to the purchaser will be repaired or replaced, as PECO elects, without charge for 
parts or labor, if the defect appears within 12 months from the date of delivery of the product to the original 
purchaser.  ALL DEFECTIVE PARTS MUST BE RETURNED TO PECO FOR INSPECTION TO DETERMINE 
VALIDITY OF WARRANTY CLAIMS.  Freight and mailing will be borne by the customer.

2.  PARTS REPLACED DURING WARRANTY:

 Any new PECO part which is furnished in performance of 

this warranty and is defective in material or workmanship as delivered to the purchaser will be repaired or 
replaced, before the expiration of the original warranty period, whichever is later.

3.  COMMERCIAL USE:

 Products put to personal use around a single household or residence is considered 

'Residential'; Products put to any business use (agricultural, commercial, or industrial) or used at multiple 
locations is considered 'Commercial.' Products designated as 'Commercial' are warrantied for 12 months
from the date of delivery of the product to the original purchaser when used for in commercial applications. 
Products designated as 'Residential' are warrantied for 90 days from the date of delivery of the product to the 
original purchaser when in commercial applications.

B.  SECURING WARRANTY ADJUSTMENTS

Call PECO for Return Authorization.  Damaged or broken parts other than engines or batteries, must be 
returned to New PECO, Inc. at 10 Walden Drive, Arden, NC 28704 before any warranty adjustment can be 
authorized. At the time of requesting warranty adjustment, the purchaser must present evidence of the date of 
delivery of the product. The purchaser shall pay any charge for the product to and from Arden, NC.

C.  ITEMS NOT COVERED BY PECO WARRANTY

Engines and batteries attached to PECO products are covered under a separate warranty by the respective 
manufacturer.

D.  UNAPPROVED ALTERATION OR MODIFICATION

All obligations of New PECO, Inc. under this warranty shall be terminated if products are altered or modified in 
ways not approved by New PECO, Inc.

E.  ACCIDENTS AND NORMAL MAINTENANC

E

The warranty covers only defective material and workmanship. It does not cover depreciation or damage 
caused by normal wear, accident, improper use or abuse of products. The cost of normal maintenance and 
normal replacement of service items such as belts, cutting blades, hoses, etc., which are not defective shall be 
paid for by the purchaser.

F.  NO REPRESENTATIONS ADDITIONAL WARRANTIES, DISCLAIMER

Neither New PECO, Inc. nor any company affiliated with it makes any warranties, representations or promises 
as to the quality of performance of its products other than those set forth herein. Except as described above, 
New PECO, Inc. makes no other warranties AND SPECIFICALLY DISCLAIMS ANY AND ALL IMPLIED 
WARRANTIES OF FITNESS AND MERCHANTABILITY.

G.  PRODUCTS USED FOR RENTAL OR LEASE PURPOSES ARE WARRANTIED FOR 45 DAYS 

FROM DATE OF ORIGINAL SALE ONLY

H.  REMEDIED EXCLUSIV

E

The only remedies the purchaser has in connection with the breach or performance of any warranty on New 
PECO, Inc. consumer products are set forth above. In no event will PECO be liable for special incidental or 
consequential damages. 

     

1.  NO SERVICE CENTER WARRANTY

The selling Service Center makes no warranty on his own on any item warranted by New PECO, Inc. unless he 
delivers to purchaser a separate written warranty certificate specifically warranting the item. The dealer has no 
authority to make any representation or promise on behalf of PECO or to modify the terms of this warranty in 
any way.

2017 (v1.0)

Содержание 28131501







































Отзывы: