KTM RC 390 страница 56 Скачать руководство пользователя

Страница: 56 / 200

COMBINATION INSTRUMENT

7.21

Setting the time

Condition

The ignition is on.
The motorcycle is stationary.

401303-01

–

Press the

MODE

button briefly and repeatedly until

ODO

appears on the display.

–

Press the

MODE

and

SET

buttons for 5 - 10 seconds.

The time display begins to flash.

–

Set the hours display using the

MODE

button.

–

Set the minutes display using the

SET

button.

–

Press the

MODE

and

SET

buttons for 5 - 10 seconds.

The time is set.

7.22

Adjusting the shift speed RPM 1

Condition

The ignition is on.
The motorcycle is stationary.

401307-01

–

Press the

MODE

button briefly and repeatedly until

TRIP 2

appears on the display.

–

Press the

MODE

button for 5 - 10 seconds.

The display

RPM 1

appears.

Info

The engine speed can be set at intervals of 50.

RPM 1

is the engine speed above which the shift warning light starts flashing.

–

Set the speed with the

MODE

and

SET

buttons.

Содержание RC 390









































































































































































































Результаты поиска

Содержание RC 390

Отзывы:

Похожие инструкции для RC 390

Бренды по названию

Популярные бренды

KTM RC 390, Руководство пользователя

Результаты поиска

Содержание RC 390

Отзывы:

Похожие инструкции для RC 390

Бренды по названию

Популярные бренды