KTM RC 390 Скачать руководство пользователя страница 111

Страница: 111 / 200

BRAKE SYSTEM

109

Warning

Environmental hazard

Hazardous substances cause environmental damage.

–

Oil, grease, filters, fuel, cleaners, brake fluid, etc., should be disposed of as stipulated in applicable regulations.

Info

Avoid contact between brake fluid and painted parts. Brake fluid attacks paint!
Use only clean brake fluid from a sealed container.

Preparatory work

–

Check the rear brake linings. (

p. 109)

M00459-10

Main work

–

Stand the vehicle upright.

–

Remove screw cap



with membrane



–

Add brake fluid to level



Brake fluid DOT 4 / DOT 5.1 (

p. 185)

–

Refit screw cap with membrane.

Info

Clean up overflowed or spilt brake fluid immediately with water.

13.8

Checking the rear brake linings

Warning

Danger of accidents

Reduced braking efficiency caused by worn brake linings.

–

Change worn brake linings immediately. (Your authorized KTM workshop will be glad to help.)

Содержание RC 390









































































































































































































Результаты поиска

Содержание RC 390

Отзывы:

KTM RC 390, Руководство пользователя, Страница: 111 / 200

Результаты поиска

Содержание RC 390

Отзывы: