KTM RC 390 страница 106 Скачать руководство пользователя

Страница: 106 / 200

BRAKE SYSTEM

104

» If the brake disc thickness is less than the specified value:

–

Change the brake discs.

–

Check the front and rear brake discs for damage, cracking, and deformation.
» If the brake disc shows signs of damage, cracking, or deformation:

–

Change the brake discs.

13.3

Checking the brake fluid level of the front brake

Warning

Danger of accidents

Failure of the brake system.

–

If the brake fluid level falls below the

MIN

mark, this indicates a leakage in the brake system or worn-out brake linings. Check

the brake system and do not continue riding. (Your authorized KTM workshop will be glad to help.)

Warning

Danger of accidents

Reduced braking efficiency due to old brake fluid.

–

Change the brake fluid of the front and rear brake according to the service schedule. (Your authorized KTM workshop will be
glad to help.)

L02132-10

–

Move the brake fluid reservoir mounted on the handlebar to a horizontal position.

–

Check the brake fluid level in viewer



» If the brake fluid level is below the

MIN

marking:

–

Add front brake fluid.

(

p. 105)

Содержание RC 390









































































































































































































Результаты поиска

Содержание RC 390

Отзывы:

Похожие инструкции для RC 390

Бренды по названию

Популярные бренды

KTM RC 390, Руководство пользователя

Результаты поиска

Содержание RC 390

Отзывы:

Похожие инструкции для RC 390

Бренды по названию

Популярные бренды