KTM LC4 ADVENTURE R 640 2000, Руководство пользователя, Страница: 33 / 46

ENGLISH
31
Fill 0.6 liters of engine oil into the can and remove the plug
5
(see page
30) next to the steering head. Introduce the plastic hose into the vent hole
B
, and fill 0.6 liters of engine oil into the frame’s front tube. Remove plastic
hose, start engine, and let it idle (approx. 20 seconds) until oil escapes at
the hole
B
.
As soon as oil starts to escape, turn off the engine, and mount the plug
together with the gasket.
Allow the engine to run until warm. Then, turn off the engine, and place
the motorbike on a flat, level surface in an upright position (center stand).
Wait for 5 minutes. Unscrew and remove the oil dipstick, and wipe it clean
with a cloth.
SCREW THE DIPSTICK IN ALL THE WAY AND REMOVE IT AGAIN.
The oil level should be between the two marks on the oil dipstick, however,
it must never rise above the MAX mark.
Otherwise, engine oil would get into the air filter box by way of the engine
venting system.
Add engine oil, if necessary.
!
CAUTION
!
– I
NSUFFICIENT OIL OR POOR QUALITY OIL RESULTS IN PREMATURE WEAR OF THE ENGINE
.
– C
HECKING THE ENGINE OIL LEVEL WHEN THE ENGINE IS COLD RESULTS IN A FALSE REA
-
DING ON THE OIL DIPSTICK AND THEREFORE AN INCORRECT OIL LEVEL
.
– D
O NOT OVERFILL THE ENGINE CASE
.
– D
O NOT UNDERFILL THE ENGINE CASE
.
Finally, check oil system and engine for leaks.
N
OTE
: D
ISPOSE OF USED OIL PROPERLY
! U
NDER NO CIRCUMSTANCES MAY USED OIL BE
DISPOSED OF IN THE SEWAGE SYSTEM OR IN THE OPEN COUNTRYSIDE
. 1
LITER OIL CON
-
TAMINATES
1.000.000
LITER WATER
.
Changing the fine screen filter *
Replace the fine screen filter when changing the engine oil.
Loosen the fine screen filter with an oil filter wrench; you will be able to
unscrew it the rest of the way with your bare hand. Let engine oil flow out
of the front pipe of the frame.
– Clean sealing surfaces on the front pipe
1
, fill new fine screen filter with
engine oil, and oil rubber gasket
2
. Replace fine screen filter and screw
it back in place, your bare hand will do.
– Start motor, bleed oil system (see Changing the engine oil) and make
sure that the fine screen filter does not leak.
!
CAUTION
!
– U
SE ONLY ORIGINAL
KTM
FINE SCREEN FILTERS
. U
SING ANOTHER FILTER BRAND CAN
RESULT IN DAMAGE TO THE ENGINE
.
– If the engine oil has been drained from the front pipe of the frame, you
must bleed the oil system !
Changing oil filter *
Replace the oil filter when changing the engine oil. Press the foot brake pedal
and place a screwdriver or similar between foot brake pedal and stopper roll so
that the oil filter cover is more accessible. Remove banjo bolt
3 and the three
screws. Remove oil filter cover 4 and oil filter. Clean filter housing, oil filter
cover, and sealing surfaces. Check oil duct in oil filter cover if clogged.
Check the O-ring 5 for damage. O-rings need not be replaced unless damaged.
Press the O-ring into the groove of the filter cover
4
. Fit new oil filter 6 with
rubber gasket on the fitting in oil filter cover and mount cover with filter.
Mount three screws and tighten with 5 Nm (4 ft.lb). Mount hollow screw
3
with seal rings and tighten with 15 Nm (11 ft.lb). Start engine and check oil
system for leakage.
3
4
5
6
2
1
3
4