KTM Freeride 350 AU страница 85 Скачать руководство пользователя | Manualshive

Страница: 85 / 116

background image

16

COOLING SYSTEM

83

16.3

Checking the coolant level

Warning

Danger of scalding

During motorcycle operation, the coolant gets very hot and is under pressure.

–

Do not remove the radiator cap, radiator hoses or other cooling system components when the engine is hot. Allow the
engine and cooling system to cool down. In case of scalding, rinse immediately with lukewarm water.

Warning

Danger of poisoning

Coolant is poisonous and a health hazard.

–

Coolant must not come into contact with the skin, eyes, or clothing. If contact occurs with the eyes, rinse with water imme-
diately and contact a physician. Immediately clean contaminated areas on the skin with soap and water. If fuel is swal-
lowed, contact a physician immediately. Change clothing that is contaminated with coolant. Keep coolant out of reach of
children.

Condition

The engine is cold.

400243-10

–

Stand the motorcycle upright on a horizontal surface.

–

Remove the radiator cap.

–

Check the coolant level in the radiator.

Coolant level



above radiator fins.

10 mm (0.39 in)

» If the coolant level does not meet specifications:

–

Correct the coolant level.

Coolant (

–

Mount the radiator cap.

16.4

Draining the coolant

Warning

Danger of scalding

During motorcycle operation, the coolant gets very hot and is under pressure.

–

Do not remove the radiator cap, radiator hoses or other cooling system components when the engine is hot. Allow the
engine and cooling system to cool down. In case of scalding, rinse immediately with lukewarm water.

Warning

Danger of poisoning

Coolant is poisonous and a health hazard.

–

Coolant must not come into contact with the skin, eyes, or clothing. If contact occurs with the eyes, rinse with water imme-
diately and contact a physician. Immediately clean contaminated areas on the skin with soap and water. If fuel is swal-
lowed, contact a physician immediately. Change clothing that is contaminated with coolant. Keep coolant out of reach of
children.

Condition

The engine is cold.

S00841-10

–

Stand the motorcycle upright.

–

Place a suitable container under the water pump cover.

–

Remove screw



. Take off radiator cap



.

–

Completely drain the coolant.

–

Mount screw



with a new seal ring and tighten it.

Guideline

Screw, water pump cover

M6

10 Nm (7.4 lbf ft)

«
...
83
84
85
86
87
...
»

Содержание Freeride 350 AU





















































































































Отзывы:

Нет отзывов

Похожие инструкции для Freeride 350 AU

Бренд: Fantic Motor Страницы: 145

Бренд: Regal Raptor Страницы: 48

2006 G 650 Xmoto

Бренд: BMW Страницы: 132

690 Enduro AUS 2010

Бренд: KTM Страницы: 265

Бренд: DYNATEK Страницы: 12

COMP-MLCS-12200

Бренд: Compcooler Страницы: 11

TOPMASTER MOVIL V0X814ST

Бренд: Shad Страницы: 2

Бренд: MINIMOTO Страницы: 20

Бренд: Can-Am Страницы: 195

Бренд: Dräger Страницы: 256

Бренд: VM Страницы: 2

Classic 350 2019

Бренд: Royal Enfield Страницы: 126

2015 RC 390 ASIA

Бренд: KTM Страницы: 196

2016 690 DUKE R

Бренд: KTM Страницы: 207

Бренд: 3M Страницы: 60

SM 500 R E4 2018

Бренд: SWM Страницы: 86

Бренд: YEC Страницы: 62

Бренд: kellermann Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды