KTM Freeride 350 AU страница 20 Скачать руководство пользователя

Страница: 20 / 116

SPEEDOMETER

7.1

Overview

401908-10

Overview of indicator lamps (

p. 14)

Left button

Display

Right button

7.2

Activation

401908-01

Activating the speedometer

The speedometer is activated when one of the buttons is pressed or an impulse comes
from the wheel speed sensor.

7.3

Message on the speedometer

401901-01

Possible states

Battery voltage of the speedometer

–

Battery voltage of the speedometer

is too low. Change the battery.

Service

–

A service is due. Contact an authorized KTM workshop.

7.4

Setting the speedometer

Condition

The motorcycle is stationary.

401909-01

–

Press both buttons for 3

–

5 seconds.

The Setup menu is displayed. The

UNIT

display flashes.

–

Press one of the buttons to select

UNIT

for the speed in kilometers

KM/H

or miles

M/H

401911-01

–

Wait for 5 seconds.

The speedometer changes to the next menu item. The

symbol flashes.

–

Press one of the buttons to select the 24h or 12h display of the clock.

Содержание Freeride 350 AU





















































































































Результаты поиска

Содержание Freeride 350 AU

Отзывы:

Похожие инструкции для Freeride 350 AU

Бренды по названию

Популярные бренды

KTM Freeride 350 AU, Руководство пользователя

Результаты поиска

Содержание Freeride 350 AU

Отзывы:

Похожие инструкции для Freeride 350 AU

Бренды по названию

Популярные бренды