KTM Freeride 350 AU страница 17 Скачать руководство пользователя

Страница: 17 / 116

CONTROLS

6.14

Idle speed adjusting screw

B01241-10

Idle speed adjusting screw



is located on the throttle valve body at the top left.

The idle speed adjusting screw has two functions.
Turning it controls the idle speed.
Pulling it out all the way raises the idle speed during a cold start.

Possible states

• RPM increase activated

–

Idle speed adjusting screw is pulled out all the way.

• RPM increase deactivated

–

Idle speed adjusting screw is pushed in all the way.

6.15

Shift lever

401950-10

Shift lever



is mounted on the left side of the engine.

401950-11

The gear positions can be seen in the photograph.
The neutral or idle position is between the first and second gears.

6.16

Foot brake lever

401956-10

Foot brake lever



is located in front of the right footrest.

The foot brake lever is used to activate the rear brake.

Содержание Freeride 350 AU





















































































































Результаты поиска

Содержание Freeride 350 AU

Отзывы:

Похожие инструкции для Freeride 350 AU

Бренды по названию

Популярные бренды

KTM Freeride 350 AU, Руководство пользователя

Результаты поиска

Содержание Freeride 350 AU

Отзывы:

Похожие инструкции для Freeride 350 AU

Бренды по названию

Популярные бренды