manualshive.com logo in svg

KTM F7103Q3, Инструкции по установке, Страница: 23 / 37

Поделиться
Скачать
KTM F7103Q3 Скачать руководство пользователя страница 23

3

WORK

21

H00935-10

–

Check the wheel bearing for damage and wear.
» If the wheel bearing is damaged or worn:

–

Change the front wheel bearing.

–

Clean and grease shaft seal rings

and contact surface

of the spacers.

Long-life grease (

p. 33)

–

Insert the spacers.

–

Lift the front wheel into the fork, position it, and insert the wheel spindle.

The brake linings are correctly positioned.

V00364-11

–

Mount and tighten screw

.

Guideline

Screw, front wheel spindle

M20x1.5

35 Nm
(25.8 lbf ft)

–

Operate the hand brake lever several times until the brake linings are seated cor-
rectly against the brake disc.

–

Remove the motorcycle from the lift stand. (

p. 16)

–

Operate the front brake and compress the fork a few times firmly.

The fork legs straighten.

–

Tighten screws

.

Guideline

Screw, fork stub

M8

15 Nm
(11.1 lbf ft)

3.11

Removing the battery (All 250/300 models, XC

‑

W US, XC

‑

W Six Days US)

Warning

Environmental hazard

 

Batteries contain environmentally-hazardous materials.

–

Do not dispose of batteries as household waste.

–

Dispose of batteries at a collection point for used batteries.

Warning

Environmental hazard

 

Hazardous substances cause environmental damage.

–

Dispose of oils, grease, filters, fuel, cleaning agents, brake fluid, etc., correctly and in compliance with the applicable regu-
lations.

Preparatory work

–

Switch off all power consumers and switch off the engine.

–

Remove the seat. (

p. 16)

F00138-10

Main work
(XC

‑

W US, XC

‑

W Six Days US, All 250/300 EU/AU/US models)

Warning

Risk of injury

 

Batteries contain harmful substances.

–

Keep batteries out of the reach of children.

–

Keep sparks and open flames away from the batteries.

–

Only charge batteries in well-ventilated rooms.

–

Maintain a minimum clearance from inflammable materials when
charging batteries.
Minimum clearance

1 m (3 ft)

–

Do not charge deeply discharged batteries if charge is already below
the minimum voltage.
Minimum voltage before the start
of the charge

9 V

–

Dispose of batteries with less than the minimum voltage correctly.

–

Disconnect negative cable

from the battery.

Содержание F7103Q3






































Отзывы:

Нет отзывов