KTM 990 Adventure AUS Скачать руководство пользователя

Страница: 49 / 218

PREPARING FOR USE

Guideline

Maximum engine speed

During the first: 1,000 km (621.4 mi)

6,500 rpm

After the first: 1,000 km (621.4 mi)

9,500 rpm

–

Avoid full-throttle operation!

6.3

Loading the vehicle

Warning

Danger of accidents

Unstable handling characteristics.

–

Do not exceed the maximum permitted weight and axle loads. The overall weight consists of: motorcycle operational and with a
full tank, driver and passenger with protective clothing and helmet, baggage.

Warning

Danger of accidents

Unstable handling characteristics due to incorrect mounting of suitcase and/or tank rucksack.

–

Mount and secure suitcase and tank rucksack according to the manufacturer's instructions.

Warning

Danger of accidents

Unstable handling characteristics at high speed.

–

Adapt your speed according to your payload. Ride more slowly if your motorcycle is loaded with cases or other baggage.
Maximum speed with luggage

130 km/h (80.8 mph)

Warning

Danger of accidents

Risk of breakage of suitcase system.

–

If you have fitted suitcases on your motorcycle, read the manufacturer's specifications concerning the maximum payload.

Содержание 990 Adventure AUS



























































































































































































































Результаты поиска

Содержание 990 Adventure AUS

Отзывы:

Похожие инструкции для 990 Adventure AUS

Бренды по названию

Популярные бренды

KTM 990 Adventure AUS, Руководство пользователя

Результаты поиска

Содержание 990 Adventure AUS

Отзывы:

Похожие инструкции для 990 Adventure AUS

Бренды по названию

Популярные бренды