KTM 990 Adventure AUS Скачать руководство пользователя

Страница: 35 / 218

CONTROLS

5.26

Combination instrument - warning of slippery roads

400894-10

The ice symbol

lights up to indicate an increased danger of slippery roads.

The ice symbol

appears in the display when the ambient temperature drops below the

specified value.

Temperature

3 °C (37 °F)

The ice symbol

goes out in the display when the ambient temperature rises above the

specified value again.

Temperature

4 °C (39 °F)

5.27

Combination instrument - coolant temperature indicator

400617-01

The temperature display consists of 12 bars. The more bars that light up, the hotter the
coolant. When the upper bar lights up, all bars in the display begin to flash and the temper-
ature warning lamp lights up.

Possible states

• Engine cold

–

Up to five bars light up.

• The engine is warm

–

Six to eleven bars light up.

• Engine hot

–

All twelve bars flash.

Содержание 990 Adventure AUS



























































































































































































































Результаты поиска

Содержание 990 Adventure AUS

Отзывы:

Похожие инструкции для 990 Adventure AUS

Бренды по названию

Популярные бренды

KTM 990 Adventure AUS, Руководство пользователя

Результаты поиска

Содержание 990 Adventure AUS

Отзывы:

Похожие инструкции для 990 Adventure AUS

Бренды по названию

Популярные бренды