KTM 990 Adventure AUS Скачать руководство пользователя страница 27

Страница: 27 / 218

CONTROLS

5.13

Combination instrument - tachometer

400916-10

The tachometer



shows the engine speed in revolutions per minute.

The red marking



shows the overspeed range of the engine.

5.14

Combination instrument - indicator lamps

400917-01

The indicator lamps offer additional information about the operating state of the motorcy-
cle.

Possible states

The turn signal indicator lamp flashes green simultaneously with the turn
signal

–

The turn signal is switched on.

The idle speed indicator lamp lights up green

–

The transmission is shifted

to idle.

The high beam indicator lamp lights up blue

–

The high beam is switched

on.

The temperature warning lamp lights up red

–

The coolant temperature has

reached a critical value.

The fuel level warning lamp lights up orange

–

The fuel level has reached

the reserve mark. The display switches to

TRIP F

Содержание 990 Adventure AUS



























































































































































































































Результаты поиска

Содержание 990 Adventure AUS

Отзывы:

KTM 990 Adventure AUS, Руководство пользователя, Страница: 27 / 218

Результаты поиска

Содержание 990 Adventure AUS

Отзывы: