KTM 990 Adventure AUS Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 218

KTM 990 Adventure AUS Скачать руководство пользователя страница 25

CONTROLS

23

A lost black ignition key must be deactivated to prevent unauthorized persons from operat-
ing the vehicle.
The second black ignition key is activated when the vehicle is shipped.
Two additional spare ignition keys (key number on the

KEYCODECARD

) can be ordered from

an authorized KTM workshop, but they must be activated before use.

5.9

Emergency OFF switch

100547-10

The emergency OFF switch



is fitted on the right side of the handlebar.

Possible states

Emergency OFF switch off

–

In this position, the ignition circuit is inter-

rupted, a running engine stops, and the engine cannot be started.

Emergency OFF switch on

–

This position is necessary for operation as it

closes the ignition circuit.

5.10

Electric starter button

100548-10

The electric starter button



is fitted on the right side of the handlebar.

Possible states

• Electric starter button

in basic position

• Electric starter button

is pressed

–

The electric starter is actuated in this position.

«
...
23
24
25
26
27
...
»

Содержание 990 Adventure AUS



























































































































































































































Отзывы:

Нет отзывов