KTM 690 DUKE R AUS/UK Скачать руководство пользователя страница 92

Страница: 92 / 187

WHEELS, TIRES

Guideline

Screw, front brake caliper

M10x1.25

45 Nm
(33.2 lbf ft)

Loctite

243™

–

Remove the fixation of the hand brake lever.

600826-10

–

Take the motorcycle off of the front wheel stand. (

p. 64)

–

Pull the front wheel brake and push down hard on the fork several times to align the
fork legs.

–

Fully tighten screws



Guideline

Screw, fork stub

15 Nm
(11.1 lbf ft)

–

Take the motorcycle off of the rear wheel stand. (

p. 65)

12.3

Removing rear wheel

–

Raise the motorcycle with the rear wheel stand. (

p. 65)

100144-10

–

Remove nut



. Remove chain adjuster



. Holding the rear wheel, withdraw the wheel

spindle



–

Push the rear wheel forward as far as possible and take the chain off the rear sprocket.

Содержание 690 DUKE R AUS/UK




























































































































































































Результаты поиска

Содержание 690 DUKE R AUS/UK

Отзывы:

KTM 690 DUKE R AUS/UK, Руководство пользователя, Страница: 92 / 187

Результаты поиска

Содержание 690 DUKE R AUS/UK

Отзывы: