manualshive.com logo in svg

KTM 640 Duke, Руководство пользователя, Страница: 7 / 52

Поделиться
Скачать
KTM 640 Duke Скачать руководство пользователя страница 7

ENGLISH

5

Hand brake lever

The hand brake lever 

1

is mounted on the right side of the handlebar.The

basic position of the handbrake lever can be changed in 4 steps 
(see Maintenance work on chassis and engine).

Speedometer

The mileage indicator 

A

in the speedometer 

2

indicates overall mileage.

The day mileage indicator 

B

can be set to 0 by means of the setting wheel 

C

.

Turn the setting wheel forward until only zeros can be seen in the display.

Tachometer

The tachometer 

3

shows the engine speed in revolutions per minute (rpm).

Do not push the engine into the orange zone, which begins at 8500 rpm.

Indicator lamps

The green indicator lamp flashes when the flasher light is working in
the same rhythm as the flasher light. Faster flashing of the flasher
control lamp indicates a defect bulb

The blue indicator lamp lights up when the high beam is on.

The green indicator lamp lights up when the neutral gear is selected

The red cooling liquid temperature warning lamp lights up as soon
as the cooling liquid has reached a temperature of approximately
110° C (230° F).

1

A

2

B

C

3

Содержание 640 Duke





















































Отзывы:

Нет отзывов