KTM 50 SX 2017 Скачать руководство пользователя | Manualshive

Страница: 77 / 104

background image

15

TUNING THE ENGINE

75

400192-11

–

Turn adjusting screw



so that there is throttle cable play



at the throttle grip.

Guideline

Play in gas throttle cable

3… 5 mm (0.12… 0.2 in)

–

Tighten nut



.

–

Slide on sleeve



.

Finishing work

–

Install the fuel tank.

–

Mount the seat. (

–

Check the play of the throttle cable. (

15.4

Carburetor - idle (50 SX)

H01455-10

The idle setting of the carburetor has a big influence on the starting behavior, stable
idling and the response to throttle opening. That means that an engine with a correctly
set idle speed is easier to start than if the idle is set wrongly.

Info

The carburetor and its components are subject to increased wear caused by
engine vibration. Wear can result in malfunctioning.

The idle speed is adjusted with idle speed adjusting screw



.

The idle mixture is adjusted with the idle mixture adjustment screw



.

15.5

Carburetor - idle (50 SX Mini)

H00078-10

The idle setting of the carburetor has a big influence on the starting behavior, stable
idling, and the response to throttle opening. This means that an engine with a correctly
set idle speed is easier to start than if the idle speed is set wrongly.

Info

The carburetor and its components are subject to increased wear caused by
engine vibration. Wear can result in malfunctioning.

The idle speed is adjusted using the idle speed adjusting screw



.

The idle mixture is adjusted using the idle air adjusting screw



.

15.6

Carburetor - adjusting idle speed (50 SX)

H01455-10

–

Screw in the idle adjusting screw



until it stops and then to the prescribed basic

setting.
Guideline

Idle mixture adjusting screw

Open

3 turns

–

Run the engine until warm.
Guideline

Warming-up phase

≥

5 min

Danger

Danger of poisoning

Exhaust gases are toxic and inhaling them may result

in unconsciousness and death.

–

Always make sure there is sufficient ventilation when running the
engine.

–

Use an effective exhaust extraction system when starting or running the
engine in an enclosed space.

–

Adjust the idle speed using the idle speed adjusting screw



.

«
...
75
76
77
78
79
...
»

Содержание 50 SX 2017









































































































Отзывы:

Нет отзывов

Похожие инструкции для 50 SX 2017

Бренд: Dakota Digital Страницы: 6

Бренд: SUR-RON Страницы: 50

Бренд: hepco & becker Страницы: 2

Бренд: Honda Страницы: 243

Scorpion Exo-T520

Бренд: Dennis Kirk Страницы: 10

Бренд: Honda Страницы: 137

SUPERSPORT1000 2003

Бренд: Ducati Страницы: 328

80 MasterGuard (L+K)

Бренд: SCHUBERTH Страницы: 44

Бренд: Yamaha Страницы: 98

Бренд: Yamaha Страницы: 108

Бренд: Yamaha Страницы: 124

ROAD STAR XV16A

Бренд: Yamaha Страницы: 117

X MAX CZD300P 2022

Бренд: Yamaha Страницы: 142

Бренд: Yamaha Страницы: 97

Бренд: Yamaha Страницы: 119

Бренд: Yamaha Страницы: 96

Бренд: hepco & becker Страницы: 4

Бренд: CATU Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды