background image

MAINTENANCE WORK ON CHASSIS AND ENGINE

82

200113-11

Refit the oil filter cover

.

Mount and tighten screws

.

Guideline

Screw, oil filter cover

M6

10 Nm (7.4 lbf ft)

Stand the motorcycle upright.

9.109

Filling up with engine oil

x

Info

Too little engine oil or poor-quality engine oil results in premature wear to the engine.

200115-10

Remove the screw cap

on the generator cover and fill up with engine oil.

Engine oil (1st
partial quantity
approx.)

0.35 l (0.37 qt.)

Engine oil (SAE 10W/50) (

p. 108)

Mount and tighten the screw connection on the generator cover.

Danger

Danger of poisoning

Exhaust gases are poisonous and inhaling them may

result in unconsciousness and/or death.

When running the engine, always make sure there is sufficient ventila-
tion, and do not start or run the engine in an enclosed space without an
effective exhaust extraction system.

Start the engine and let it run idle for 30 seconds.

Stop the engine and check that it is oil-tight.

301454-10

Stand the motorcycle upright on a horizontal surface.

Remove the screw connection on the generator cover.

Fill in engine oil to the upper half of level viewer

.

Engine oil (total
filling capacity
approx.)

0.60 l (0.63 qt.)

Engine oil (SAE 10W/50) (

p. 108)

Mount and tighten the screw connection on the generator cover.

9.110

Topping up engine oil

Info

Too little engine oil or poor-quality engine oil results in premature wear to the engine.

200115-10

Remove the screw cap

on the generator cover and fill up with engine oil.

Engine oil (SAE 10W/50) (

p. 108)

Mount and tighten screw cap

.

Danger

Danger of poisoning

Exhaust gases are poisonous and inhaling them may

result in unconsciousness and/or death.

When running the engine, always make sure there is sufficient ventila-
tion, and do not start or run the engine in an enclosed space without an
effective exhaust extraction system.

Start the engine and check that it is oil-tight.

Check the engine oil level. (

p. 80)

Содержание 450 XC-W SIX DAYS USA 2010























































































































Отзывы: