manualshive.com logo in svg

KTM 450 XC-W SIX DAYS USA 2010, Руководство пользователя, Страница: 69 / 118

Поделиться
Скачать
KTM 450 XC-W SIX DAYS USA 2010 Скачать руководство пользователя страница 69

MAINTENANCE WORK ON CHASSIS AND ENGINE

67

9.72

Removing the battery

x

Warning

Risk of injury

 

Battery acid and battery gases cause serious cauterization.

–

Keep batteries out of the reach of children.

–

Wear suitable protective clothing and goggles.

–

Avoid contact with battery acid and battery gases.

–

Keep the battery away from sparks or open fire. Charge only in well ventilated rooms.

–

In the event of skin contact, rinse with large amounts of water. If battery acid gets in the eyes, rinse with water for at least
15 minutes and contact a doctor.

–

Switch off all power-consuming components and switch off the engine.

–

Remove the seat. (

p. 69)

500069-10

–

Disconnect the negative (minus) cable

of the battery.

–

Pull back the plus pole cover

and disconnect the positive (plus) cable of the bat-

tery.

–

Hang the rubber band

out to the bottom.

–

Lift the battery up.

9.73

Installing the battery

x

500069-11

–

Place the battery in the battery holder.

4Ah battery (YTX5L-BS) (

p. 96)

–

Reconnect the rubber band

.

–

Attach the plus cable and replace the plus pole cover

.

–

Attach the minus cable

.

–

Mount the seat. (

p. 70)

9.74

Recharging the battery

x

Warning

Risk of injury

 

Battery acid and battery gases cause serious cauterization.

–

Keep batteries out of the reach of children.

–

Wear suitable protective clothing and goggles.

–

Avoid contact with battery acid and battery gases.

–

Keep the battery away from sparks or open fire. Charge only in well ventilated rooms.

–

In the event of skin contact, rinse with large amounts of water. If battery acid gets in the eyes, rinse with water for at least
15 minutes and contact a doctor.

Warning

Environmental hazard

 

Battery parts and acid are harmful to the environment.

–

Do not discard batteries with the household trash. Dispose of a defective battery in an environmentally compatible manner.
Give the battery to your KTM dealer or to a recycling center that accepts used batteries.

Warning

Environmental hazard

 

Hazardous substances cause environmental damage.

–

Oil, grease, filters, fuel, cleaners, brake fluid, etc., should be disposed of as stipulated in applicable regulations.

Содержание 450 XC-W SIX DAYS USA 2010























































































































Отзывы:

Нет отзывов