KTM 450 SMR 2021 Скачать руководство пользователя

Страница: 54 / 139

11 SERVICE WORK ON THE CHASSIS

11.18

Removing the shock absorber

Preparatory work

–

Raise the motorcycle with a lift stand. (

p. 42)

F01527-10

Main work

–

Remove the cable ties.

–

Remove screws

along with the washers.

–

Remove screw

–

Take off the left frame protector.

–

Push the right frame protector to the front and take off at the
bottom.

E01957-10

–

Remove screw

–

Remove fitting

Info

Raise the swingarm slightly to be able to remove the
screws more easily.

E01958-10

–

Press angle lever

toward the rear.

–

Press linkage lever

downward.

E01959-10

–

Remove screws

–

Pull off foot brake cylinder from the push rod.

120320-01

–

Remove the connecting link of the chain.

–

Take off the chain.

Info

Cover the components to protect them against damage.

Содержание 450 SMR 2021












































































































































Результаты поиска

Содержание 450 SMR 2021

Отзывы:

Похожие инструкции для 450 SMR 2021

Бренды по названию

Популярные бренды

KTM 450 SMR 2021, Руководство пользователя

Результаты поиска

Содержание 450 SMR 2021

Отзывы:

Похожие инструкции для 450 SMR 2021

Бренды по названию

Популярные бренды