KTM 450 SMR 2021 Скачать руководство пользователя страница 41

Страница: 41 / 139

TUNING THE CHASSIS 10

When disconnecting, excess pressure will escape from the
hose

–

the fork leg itself does not lose any air.

The fork airpump indicator switches off automatically after
80 seconds.

–

Mount the protection cap.

Info

Only tighten the protection cap by hand.

Finishing work

–

Remove the motorcycle from the lift stand. (

p. 42)

10.14

Adjusting the compression damping of the fork

Info

The hydraulic compression damping determines the fork suspension behavior.

V01856-10

–

Turn adjusting screw

clockwise all the way.

Info

Adjusting screw

is located at the upper end of the

right fork leg.

–

Turn counterclockwise by the number of clicks corresponding
to the fork type.
Guideline

Compression damping

Comfort

17 clicks

Standard

12 clicks

Sport

7 clicks

Info

Turn clockwise to increase damping; turn counterclock-
wise to reduce damping during compression.

10.15

Adjusting the rebound damping of the fork

Info

The hydraulic rebound damping determines the fork suspension behavior.

M01100-11

–

Take off protection cap

–

Turn adjusting screw

clockwise all the way.

Info

Adjusting screw

is located at the lower end of the

right fork leg.

–

Turn counterclockwise by the number of clicks corresponding
to the fork type.

Содержание 450 SMR 2021












































































































































Результаты поиска

Содержание 450 SMR 2021

Отзывы:

Бренды по названию

Популярные бренды

KTM 450 SMR 2021, Руководство пользователя

Результаты поиска

Содержание 450 SMR 2021

Отзывы:

Бренды по названию

Популярные бренды