background image

3 WORK

28

(250 EXC

F BR)

Warning

Risk of injury

Battery acid and battery gases cause

serious chemical burns.

Keep 12 V batteries out of the reach of chil-
dren.

Wear suitable protective clothing and safety
glasses.

Avoid contact with battery acid and battery
gases.

Keep sparks or open flames away from the
12 V battery.

Only charge 12 V batteries in well-ventilated
rooms.

Rinse the affected area immediately with
plenty of water in the event of contact with the
skin.

Rinse eyes with water for at least 15 minutes
and consult a doctor immediately if battery
acid and battery gases get into the eyes.

Disconnect negative cable

1

from the 12 V battery.

Pull back positive terminal cover

2

and disconnect the

positive cable from the 12 V battery.

Remove screw

3

.

Pull holding bracket

4

forward and remove the 12 V bat-

tery upwards.

3.14

Installing the 12 V battery

H00386-10

Main work

Insert the 12 V battery into the battery compartment with the
terminals facing forward and secure with holding bracket

1

.

(EXC

F EU/AU/US/AR, EXC

F Six Days)

12 V battery (HJTZ5S-FP-C)

(250 EXC

F BR)

12 V battery (YTX5L-BS)

Mount and tighten screw

2

.

Guideline

Remaining screws,
chassis

M6

10 Nm (7.4 lbf ft)

Connect positive cable

3

to the 12 V battery.

Guideline

Screw, battery termi-
nal

M5

2.5 Nm
(1.84 lbf ft)

Slide positive terminal cover

7

over the positive terminal.

Connect negative cable

4

to the 12 V battery.

Содержание 250 EXC-F 2019

















































Отзывы: