background image

MAINTENANCE WORK ON CHASSIS AND ENGINE

57

600087-11

Mount and tighten screws

.

Guideline

Remaining screws, chassis

M8

25 Nm
(18.4 lbf ft)

Connect the hoses

of the fuel tank breather without kinking.

Mount the seat. (

p. 56)

Mount the trim. (

p. 55)

8.65

Folding up the fuel tank at the rear

Danger

Fire hazard

Fuel can easily catch fire.

Never fill up the vehicle near open flames or burning cigarettes, and always switch off the engine first. Be careful that no
fuel is spilt, especially on hot vehicle components. Clean up spilt fuel immediately.

Fuel in the fuel tank expands when warm and can escape if the tank is overfilled. See specifications on filling up with fuel.

Warning

Danger of poisoning

Fuel is poisonous and a health hazard.

Avoid contact between fuel and skin, eyes and clothing. Do not inhale fuel vapors. If fuel gets into your eyes, rinse immedi-
ately with water and contact a doctor. Wash affected skin areas immediately with soap and water. If fuel is swallowed, con-
tact a doctor immediately. Change clothing that has come into contact with fuel. Store fuel in a suitable canister according
to regulations and keep it out of the reach of children.

Remove the seat. (

p. 55)

600090-10

Loosen the screw

on both sides.

Remove screws

and

on both sides.

Remove the main silencer

on both sides.

600092-10

Open the quick release of the fuel line

.

Remove screw

.

Содержание 2009 690 Rally Factory Replica









































































































Отзывы: