background image

3

WORK

12

Switch off the battery charger after charging and disconnect from the battery.
Guideline

The charging current, charging voltage, and charging time must not be exceeded.
Charge the battery regularly when the
motorcycle is not in use

3 months

Connect the negative cable with the battery.

Finishing work

Mount the seat. (

p. 10)

3.10

Installing the battery (All XC models)

H00383-10

Main work

Insert the battery into the battery compartment with the terminals facing forward.

Battery (YTX4L-BS)

Reconnect rubber band

.

Position the positive cable

and mount and tighten the screw.

Guideline

Screw, battery terminal

M5

2.5 Nm
(1.84 lbf ft)

Info

Contact disks

must be mounted under screws

and cable sockets

with the claws toward the battery terminal.

Slide positive terminal cover

over the positive terminal.

Position negative cable

and mount and tighten the screw.

Guideline

Screw, battery terminal

M5

2.5 Nm
(1.84 lbf ft)

Finishing work

Mount the seat. (

p. 10)

3.11

Opening the filler cap

Danger

Fire hazard

Fuel is highly flammable.

Never refuel the vehicle near open flames or burning cigarettes, and always switch off the engine first. Be careful that no
fuel is spilt, especially on hot vehicle components. Clean up spilt fuel immediately.

The fuel in the fuel tank expands when warm and may emerge if overfilled. Follow the instructions on refueling.

Warning

Danger of poisoning

Fuel is poisonous and a health hazard.

Fuel must not come into contact with the skin, eyes, or clothing. Do not breathe in the fuel vapors. If contact occurs with
the eyes, rinse with water immediately and contact a physician. Immediately clean contaminated areas on the skin with
soap and water. If fuel is swallowed, contact a physician immediately. Change clothing that has been contaminated with
fuel. Store fuel properly in a suitable canister and keep away from children.

Warning

Environmental hazard

Improper handling of fuel is a danger to the environment.

Do not allow fuel to get into the ground water, the ground, or the sewage system.

Содержание 125 SX 2016























Отзывы: