KStar MEMO PLUS RT II (MP9100RTII-0.9) 1-3K Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 50

background image

42

Fig.24 Remove the battery park

5.Hold the middle of the new battery pack, insert it. Once install the new battery pack, make sure it is

completely inserted into the chassis as fig

25

shown.

Fig.25 Installation for battery pack

0T

Testing New Batteries

0T

To test new batteries:

0T

1. Plug the UPS into a power outlet for 48 hours to charge the

0T

batteries.

0T

2. Start up the UPS by pressing the start up combination button.

0T

3. Press the battery test combination button to activate the battery test.

0T

The UPS starts a battery test if the batteries are fully charged, the

0T

UPS is in Normal mode with no active alarms, and the bypass

0T

voltage is acceptable.

0T

During the battery test, the UPS transfers to Battery mode and

«
...
40
41
42
43
44
...
»

Содержание MEMO PLUS RT II (MP9100RTII-0.9) 1-3K



















































Отзывы:

Нет отзывов

Похожие инструкции для MEMO PLUS RT II (MP9100RTII-0.9) 1-3K

Бренд: Ewent Страницы: 61

PowerWave 3000T

Бренд: Uninterruptible Power Supplies Страницы: 60

Бренд: Quer Страницы: 28

Zenergy Station 2000

Бренд: INFOSEC UPS SYSTEM Страницы: 27

Бренд: Eaton Страницы: 164

Бренд: Altronix Страницы: 4

Бренд: Eaton Страницы: 124

Бренд: Powertronix Страницы: 33

SmartPro SMX1200XLHG

Бренд: Tripp Lite Страницы: 5

SmartPro SMART3000RMXL2U

Бренд: Tripp Lite Страницы: 6

SmartPro Rackmount SMX3000XLRT2U

Бренд: Tripp Lite Страницы: 6

SmartPro Rackmount SMX1000RT2U

Бренд: Tripp Lite Страницы: 6

SmartPro SMX2200XLRT2U

Бренд: Tripp Lite Страницы: 60

Бренд: Eaton Страницы: 28

Triathlon III T3UPS-11-20K

Бренд: Georator Страницы: 98

Бренд: Unitek Страницы: 24

RACKMOUNT UPS PLUS FN3KRM-2

Бренд: Falcon Страницы: 44

Digital Energy VH 700

Бренд: GE Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды