KStar MEMO PLUS RT II (MP9100RTII-0.9) 1-3K Скачать руководство пользователя страница 40

Страница: 40 / 50

UPS Maintenance

This section explains how to:



Care for the UPS and batteries



Replace Extended Battery Packs(EBPs)



Test new batteries



Recycle used batteries or UPS

UPS and Battery Care

For the best preventive maintenance, keep the area around the UPS clean and dust‐

free. If the atmosphere is very dusty, clean the outside of the system with a vacuum

cleaner. For full battery life, keep the UPS at an ambient temperature of 25°C (77°F).

NOTE

The batteries in the UPS are rated for a 3–5 year service life. The length of

service life varies, depending on the frequency of usage and ambient temperature.

Batteries used beyond expected service life will often have severely reduced

runtimes. Replace batteries at least every 5 years to keep units running at peak

efficiency.

Storing the UPS and Batteries

If you store the UPS for a long period, recharge the battery every 6 months by

connecting the UPS to utility power. The internal batteries charge to 80% capacity in

less than 5 hours. However, we recommends that the batteries charge for 48 hours

after long-term storage. If optional EBPs are installed, see the recharge times listed

in Table 21 on page

. Check the battery recharge date on the shipping carton label.

If the date is expired and the batteries were never recharged, do not use the UPS.

Contact your service representative.

Replacing Batteries

NOTE

DO NOT DISCONNECT the batteries while the UPS is in Battery mode.

。

The EBP can be replaced when UPS is ON， but be aware that if the utility fails at that

time , the load of the UPS may NOT be protected.

If you prefer to remove input power to change the batteries, see “UPS Turn on and

Turn off” on page

Содержание MEMO PLUS RT II (MP9100RTII-0.9) 1-3K



















































Результаты поиска

Содержание MEMO PLUS RT II (MP9100RTII-0.9) 1-3K

Отзывы:

Похожие инструкции для MEMO PLUS RT II (MP9100RTII-0.9) 1-3K

Бренды по названию

Популярные бренды

KStar MEMO PLUS RT II (MP9100RTII-0.9) 1-3K, Руководство пользователя

Результаты поиска

Содержание MEMO PLUS RT II (MP9100RTII-0.9) 1-3K

Отзывы:

Похожие инструкции для MEMO PLUS RT II (MP9100RTII-0.9) 1-3K

Бренды по названию

Популярные бренды