KStar MEMO PLUS RT II (MP9100RTII-0.9) 1-3K Скачать руководство пользователя страница 37

Страница: 37 / 50

Connectivity Cards

Connectivity cards allow the UPS to communicate in a variety of

networking environments and with different types of devices. The UPS has one

available communication bay for the following connectivity cards:

●

Web/SNMP Card

- has SNMP and HTTP capabilities as well as monitoring

through a Web browser interface; connects to a twisted-pair Ethernet

(10/100BaseT) network. In addition, a Environmental Monitoring Probe can be

attached to obtain humidity, temperature, smoke alarm, and security information.

●

Relay Interface Card

- has isolated dry contact relay outputs for UPS status:

Utility failure, Low battery, UPS alarm/OK, or On bypass.

See Figure

17, 18

on page

for the location of the communication bay.

Figure 20 Optional Connectivity Cards

NOTE：

Before installing the connectivity card , please remove the clip from the bay.

Refer to the user’s manual of the appropriate cards.

Emergency Power-off

EPO is used to shut down the UPS from a distance. This feature can be used for

shutting down the load and the UPS by thermal relay, for instance in the event of

room overtemperature. When EPO is activated, the UPS shuts down the output and

all its power converters immediately. The UPS remains on to alarm the fault.

There is also a front panel EPO option for user to initial EPO function by pressing the

three switch on the front panel together. When the three switches is pressed down

at the same time, the EPO function will be actived, UPS will shutdown and the buzzer

will long beep. Pressing startup switches will not turn on the UPS unless the EPO

function is deactived by pressing the three switches together and press off switches

to return normal status.

WARNING

The EPO circuit is an IEC 60950 safety extra low voltage (SELV) circuit. This circuit

must be separated from any hazardous voltage circuits by reinforced insulation.

CAUTION

● The EPO must not be connected to any utility connected circuits. Reinforced

insulation to the utility is required. The EPO switch must have a minimum rating of

24 Vdc and 20 mA and be a dedicated latching-type switch not tied into another

circuit. The EPO signal must remain active for at least 250 ms for proper operation.

● To ensure the UPS stops supplying power to the load during any mode of

operation, the input power must be disconnected from the UPS when the

Содержание MEMO PLUS RT II (MP9100RTII-0.9) 1-3K



















































Результаты поиска

Содержание MEMO PLUS RT II (MP9100RTII-0.9) 1-3K

Отзывы:

Похожие инструкции для MEMO PLUS RT II (MP9100RTII-0.9) 1-3K

Бренды по названию

Популярные бренды

KStar MEMO PLUS RT II (MP9100RTII-0.9) 1-3K, Руководство пользователя

Результаты поиска

Содержание MEMO PLUS RT II (MP9100RTII-0.9) 1-3K

Отзывы:

Похожие инструкции для MEMO PLUS RT II (MP9100RTII-0.9) 1-3K

Бренды по названию

Популярные бренды