5
EN
PROGRAMMATION
LED FUNCTIONS
PROGRAMMATION OF RADIO MODULE USING LARES CONTROL PANEL
PROGRAMMATION OF RADIO MODULE AS STAND-ALONE DEVICE
Powering it up, the LED on device quickly blinks 3 times. Once stops blinking, if there are programmed opera remote commands and the device is
working in stand-alone mode, the led stays lit. If the device works as a wireless peripheral of the panel, the led turns OFF. Once the starting phase
is over, the led indicates the reception of a valid radio command.
In order to work with the
lares
control panels,
auxi wls
has to be enrolled as peripheral. The different ways to enroll an
auxi wls
are decribed here
below:
1.
Insert the serial number of
auxi wls
directly from
basis
software
2.
Set the panel on ‘Enrolling’ mode and power up the
auxi wls
3.
Set the panel on ‘Enrolling’ mode and press shortly on programmation button on
auxi wls
The outputs and the inputs can be programmed as normally open or normally closed. Please refer to the
lares
programmation manual for more
details
In order to program
auxi wls
as stand-alone device, at least an
opera
remote command has to be memorized. The procedures to memorize an
opera
remote command and to program the relay outputs are described here below.
MEMORIZE OPERA REMOTE COMMANDS
In order to program the remote commands, hold the programmation button on
auxi wls
for 3 seconds. The led on device stays lit to confirm the
access on programmation mode. Hold the key on remote command for 3 seconds, in order to memorize it. The led on
auxi wls
blinks 4 times to
confirm the memorization. It could be usefull to use the same
opera
to manage more
auxi wls
placed on the same radio operational range. To
do this, avoiding conflicts, just associate a single key of remote command to a single
auxi wls
. In order to associate only one key to an
auxi wls
,
press the key you want to associate ( - -
) within the 5 seconds after the confirm of memorization. A memorized remote command can be
deleted by holding for 3 second the key. The led on
auxi wls
quickly blinks 2 couple of times in order to confirm the deleted remote command.
PROGRAMMATION OF FUNCTIONS OF RELAY OUTPUTS
Once the memorization of remote commands is over, by holding for 3 seconds the programmation button on
auxi wls
, it switches from the
programmation of remote commands to the programmation of outputs. While in outputs programmation mode, the led on
auxi wls
blinks
regularly (
half a second ON, half a second OFF
). At this point, a memorized remote command can be used to program the outputs. Please see
the table here below to program the outputs.
INDIPENDENT
MONOSTABLE
relay output
1
Short pression on key of
opera
remote command. Once pressed, the first relay switches
and the led on
auxi wls
starts blinking each second. This indicates that
auxi wls
start
counting the monostable time. By pressing again, the relay re-opens and the led on
auxi
wls
quickly blinks 3 times to confirm the configuration saving. The monostable time is the
time elapsed between the two pressions on key.
relay output
2
Short pression on key of
opera
remote command. Once pressed, the first relay switches
and the led on
auxi wls
starts blinking each second. This indicates that
auxi wls
start
counting the monostable time. By pressing again, the relay re-opens and the led on
auxi
wls
quickly blinks 3 times to confirm the configuration saving. The monostable time is the
time elapsed between the two pressions on key.
BISTABLE
relay output
1
Long pression on key . The led on
auxi wls
blinks 3 times to confirm the configuration
saving
relay output
2
Long pression on key . The led on
auxi wls
blinks 3 times to confirm the configuration
saving
SPTD
Change over
switch
MONOSTABLE
Short pression on key of
opera
remote control. Once pressed, the first relay switches and the led on
auxi
wls
starts blinking each second. This indicates that
auxi wls
start counting the monostable time. By pressing
again, the relay re-opens and the led on
auxi wls
quickly blinks 3 times to confirm the configuration saving.
The monostable time is the time elapsed between the two pressions on key.
BISTABLE
Long pression on key of
opera
remote control. The led on
auxi wls
quickly blinks 3 times to confirm the
configuration saving.
INTERLOCKED
MONOSTABLE
Short pression on key of
opera
remote command. Once pressed, the first relay switches and the led on
auxi wls
starts blinking each second. This indicates that
auxi wls
start counting the monostable time. By
pressing again, the relay re-opens and the led on
auxi wls
quickly blinks 3 times to confirm the configuration
saving. The monostable time is the time elapsed between the two pressions on key.
BISTABLE
Long pression on key of
opera
remote control. The led on
auxi wls
quickly blinks 3 times to confirm the
configuration saving.
By holding for 3 seconds the programmation button on
auxi wls
, it exits from the outputs programmation and the device returns to normal working
mode. The led on device blinks as the start of programmation, to confirm its end.
NOTE:
auxi wls
have to be programmed one by one. DO NOT try to program more than one auxi at the same time, to avoid conflicts.
