KSB PumpDrive Скачать руководство пользователя страница 40

Страница: 40 / 162

⇨

The LED bar graph display returns to operating parameter display mode, i.e.

the LEDs are steadily lit.

6.1.6

Setting the dynamic pressure setpoint compensation function

Press the Func parameterisable function key.

⇨

The dynamic pressure setpoint compensation function (dynamic differential
pressure setpoint compensation) is activated (

⇨

Section 7.2.4.1 Page 85) .

Press OK.

⇨

The percentage of the setpoint compensation of the dynamic pressure
setpoint compensation function is displayed in the bar graph display by
flashing yellow LEDs.

Press the Func parameterisable function key.

⇨

Display of the dynamic pressure setpoint compensation function is
deactivated.

6.2 Graphical control panel

Fig. 22: Graphical control panel
Table 30: Description of graphical control panel

Item

Description

Function

LED traffic light
function

The traffic light function provides information
about the system's operating status.

Graphical display

Information about PumpDrive operation is
displayed.

Navigation keys

Navigation and parameter setting

Operating keys

Toggling operating modes

Service interface

PumpDrive configuration and parameterisation
via PC/notebook

Menu keys

Accessing the elements of the first menu level

Graphical control panel

6 Operation

40 of 162

PumpDrive

Содержание PumpDrive



































































































































































Результаты поиска

Содержание PumpDrive

Отзывы:

Похожие инструкции для PumpDrive

Бренды по названию

Популярные бренды

KSB PumpDrive, Инструкция по установке и эксплуатации

Результаты поиска

Содержание PumpDrive

Отзывы:

Похожие инструкции для PumpDrive

Бренды по названию

Популярные бренды