KSB PumpDrive Скачать руководство пользователя страница 158

Страница: 158 / 162

14 EC Declaration of Conformity

Manufacturer:

KSB Aktiengesellschaft

Johann-Klein-Straße 9

67227 Frankenthal (Germany)

The manufacturer herewith declares that the product:

PumpDrive

KSB order number: ...................................................................................................

▪

is in conformity with the provisions of the following Directives as amended from time to time:

– Low-voltage Directive 2006/95/EC
– Electromagnetic Compatibility Directive 2004/108/EC

The manufacturer also declares that

▪

the following harmonised international standards have been applied:

– EN 61800-3, ≤ 7.5 kW: EN 61000-6-3, > 7.5 kW: EN 6100-6-2,
– EN 55011+A1/+A2,
– EN 61000-3-2, EN 61000-3-3, EN 61000-3-11,
– EN 61000-6-1, EN 61000-6-4,
– EN 60204-1,
– EN 61800-5-1,
– EN 50178

▪

Applied national technical standards and specifications, in particular:

– EN 60034 (VDE 0530)

The EC Declaration of Conformity was issued in/on:

Frankenthal, 14.11.2007

Joachim Schullerer

Head of Product Development

Automation Products

KSB Aktiengesellschaft

Johann-Klein-Straße 9

67227 Frankenthal (Germany)

14 EC Declaration of Conformity

158 of 162

PumpDrive

Содержание PumpDrive



































































































































































Результаты поиска

Содержание PumpDrive

Отзывы:

Похожие инструкции для PumpDrive

Бренды по названию

Популярные бренды

KSB PumpDrive, Инструкция по установке и эксплуатации

Результаты поиска

Содержание PumpDrive

Отзывы:

Похожие инструкции для PumpDrive

Бренды по названию

Популярные бренды