KSB Magnochem-Bloc Скачать руководство пользователя страница 77 | Manualshive

Страница: 77 / 96

background image

8 Trouble-shooting

77 of 96

Magnochem-Bloc

8 Trouble-shooting

WARNING

Improper work to remedy faults

Risk of injury!

▷

For any work performed to remedy faults, observe the relevant information
given in this operating manual and/or in the product literature provided by the
accessories manufacturer.

If problems occur that are not described in the following table, consultation with the
KSB customer service is required.

A

Pump delivers insufficient flow rate

B

Motor is overloaded

C

Excessive discharge pressure

D

Leakage at the pump

E

Vibrations during pump operation

F

Impermissible temperature increase in the pump

Table 21:

Trouble-shooting

A B C D E

F Possible causes

Remedy

10)

✘

-

-

-

-

- Pump delivers against an excessively high

pressure.

Re-adjust to duty point.

Check system for impurities.
Fit a larger impeller.

11)

Increase the speed (turbine, I.C. engine).

✘

-

-

-

✘ ✘

Pump or piping are not completely vented
and/or primed.

Vent and/or prime.

✘ ✘

-

-

✘

- Supply line or impeller clogged

Remove deposits in the pump and/or piping.

✘

-

-

-

-

- Formation of air pockets in the piping

Alter piping layout.
Fit a vent valve.

✘

-

-

-

✘ ✘

NPSH

available

(positive suction head) is too low.

Check/alter fluid level.
Fully open the shut-off element in the suction
line.
Change suction line, if the friction losses in the
suction line are too high.
Check any strainers installed/suction opening.
Observe permissible speed of pressure fall.

✘

-

-

-

-

- Increased axial thrust

11)

Correct rotor adjustment.

✘

-

-

-

-

- Wrong direction of rotation

Check the electrical connection of the motor
and the control system, if any.

✘

-

-

-

-

- Speed is too low.

11)

▪

Operation with frequency inverter

▪

Operation without frequency inverter

▪

Increase voltage/frequency at the
frequency inverter in the permissible
range.

▪

Check voltage.

✘

-

-

-

✘

- Suction lift is too high.

Clean suction strainer and suction lines.
Correct/alter fluid level.
Change suction line.

-

✘

-

-

✘

- Pump back pressure is lower than specified in

the purchase order.

Adjust duty point accurately by means of the
shut-off element.
In the case of persistent overloading, turn
down impeller.

11)

-

✘

-

-

-

- Density or viscosity of fluid handled higher

than stated in purchase order

11)

10)

Release pump pressure before attempting to remedy faults on parts which are subjected to pressure.

11)

Consult the manufacturer.

«
...
75
76
77
78
79
...
»

Содержание Magnochem-Bloc

































































































Отзывы:

Нет отзывов

Похожие инструкции для Magnochem-Bloc

Бренд: WattNode Страницы: 57

Бренд: Kanomax Страницы: 31

Бренд: Hach Страницы: 196

Бренд: Keithley Страницы: 73

Бренд: Macnaught Страницы: 4

Бренд: Narvitech Страницы: 2

Бренд: Qu-Bit Electronix Страницы: 10

Бренд: Ralston Instruments Страницы: 52

Бренд: WATERGUARD Страницы: 2

HYDROMETTE HB 30

Бренд: GANN Страницы: 65

Бренд: DriveTest Страницы: 24

Бренд: Mannix Страницы: 5

Бренд: OHAUS Страницы: 84

Бренд: Kawai Страницы: 72

Бренд: PCE Instruments Страницы: 6

Бренд: PASI Страницы: 59

Бренд: Lutron Electronics Страницы: 10

Бренд: Hanna Instruments Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды