KSB Magnochem-Bloc Скачать руководство пользователя страница 21

Страница: 21 / 96

5 Installation at Site

21 of 96

Magnochem-Bloc

5 Installation at Site

5.1 Safety regulations

DANGER

Strong magnetic field in the area of the magnetic coupling or the individual
magnets

Danger of death for persons with pacemaker!

Interference with magnetic data carriers, electronic devices, components and
instruments!

Uncontrolled magnetic attraction forces between magnet-equipped components,
tools or similar!

▷

Keep a safety distance of at least 0.3 m.

▷

Also observe the additional instructions. (

Section 2.10, Page 12)

5.2 Checks to be carried out prior to installation

Place of installation

WARNING

Installation on mounting surface which is unsecured and cannot support the load

Personal injury and damage to property!

▷

Use a concrete of compressive strength class C12/15 which meets the
requirements of exposure class XC1 to EN 206-1.

▷

The mounting surface must be set, flat, and level.

▷

Observe the weights indicated.

1. Check the structural requirements.

All structural work required must have been prepared in accordance with the
dimensions stated in the outline drawing/general arrangement drawing.

5.3 Installing the pump set

DANGER

Excessive temperatures due to improper installation

Explosion hazard!

▷

Install the pump in a horizontal position to ensure self-venting of the pump.

▷

In external circulation and dead-end configuration operating modes, vent the
rotor space separately via the auxiliary connections at the casing cover.

DANGER

Static charging due to insufficient potential equalisation

Explosion hazard!

▷

Make sure that the connection between pump and baseplate is electrically
conductive.

Up to motor size 132

Up to motor size 132, the motor is flange-mounted to the pump lantern without a
support foot.

Motor sizes 160 and 180

The motor weight is transmitted to the foundation via a support foot. The support
foot is not bolted to the foundation.

From motor size 200

From motor size 200, motors with feet are required and used for installation.

Содержание Magnochem-Bloc

































































































Результаты поиска

Содержание Magnochem-Bloc

Отзывы:

Похожие инструкции для Magnochem-Bloc

Бренды по названию

Популярные бренды

KSB Magnochem-Bloc, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Magnochem-Bloc

Отзывы:

Похожие инструкции для Magnochem-Bloc

Бренды по названию

Популярные бренды