manualshive.com logo in svg

KSB Etanorm FXV, Инструкция по установке и эксплуатации

Поделиться
Скачать
KSB Etanorm FXV Скачать руководство пользователя страница 22

5 Installation at Site

22 of 62

Etanorm FXV

1311.83/06-EN

-

30

20

70

120

140

G

S

B

0,7

0,8

0,9

1

1,1

1,3

1,2

°C

Correction coefficient

Fig. 10: 

Temperature/material correction diagram for casing materials G (EN-GJL-250/

A48CL35B), S (EN-GJS-400-15/A536 GR 60-40-18) and B (CC480K-GS/B30 C90700)

5.4.3 Auxiliary connections

 WARNING

Failure to use or incorrect use of auxiliary connections (e.g. barrier fluid, flushing
liquid, etc.)

Risk of injury from escaping fluid!

Risk of burns!

Malfunction of the pump!

▷

Refer to the general arrangement drawing, the piping layout and pump
markings (if any) for the quantity, dimensions and locations of auxiliary
connections.

▷

Use the auxiliary connections provided.

5.5 Enclosure/insulation

CAUTION

Heat build-up in the bearing bracket

Damage to the bearing!

▷

Never insulate the bearing bracket, bearing bracket lantern and casing cover.

5.6 Checking the coupling alignment

CAUTION

Misalignment of pump and motor shafts

Damage to pump, motor and coupling!

▷

Always check the coupling after the pump has been installed and connected to
the piping.

▷

Also check the coupling of pump sets supplied with pump and motor mounted
on the same baseplate.

Содержание Etanorm FXV































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды